WARNING!
Ensure all preliminary checks are carefully carried out before use of jack. Immediately repair or replace damaged parts
(use authorised service agent). Ensure use of genuine parts only. Non authorised parts may be dangerous and will invalidate the warranty.
WARNING! Use jack on level and solid ground, preferably concrete. Ensure the floor over which the jack will be transported is swept clean.
DANGER! DO NOT use on tarmacadam, or any other soft surface as jack may sink or topple. Serious personal or fatal injury may result.
DANGER! If jack tips or leans STOp whAT yOuR ARE DOING. MOVE QuICKLy TO A SAFE DISTANCE. DO NOT TRy TO hOLD OR
STEADy JACK. Serious personal or fatal injury may result.
Use jack in an adequate working area for its function, keep area clean & tidy and free from unrelated materials. Ensure there is adequate lighting.
Before use ensure the gearbox weight and size does not exceed the capacity of the jack.
Ensure the vehicle is raised and stabilised at the correct height before attempting to move the jack under the vehicle.
Keep all unauthorised persons away from the jack during lifting and lowering and when in transit.
Maintain correct balance and footing. Ensure the floor is not slippery and wear non slip shoes.
Remove ill fitting clothing. Remove ties, watches, rings, and other loose jewellery, and contain and/or tie back long hair.
WARNING! Ensure load is placed level and centrally on jack saddle and load is fixed in place before attempting to lift, lower, or transport.
The lowering speed will vary according to the weight of the load and the release valve setting.
Ensure the jack saddle is fully lowered and is clean, dry, and oil free before attempting to move the jack with or without a load.
Diligence is required in ensuring that you continually monitor any operation until completed.
WARNING! DO NOT operate jack if any parts are damaged or missing.
DO NOT
exceed the rated capacity of the jack.
DO NOT
allow untrained persons to operate the jack.
DO NOT
place any part of your body within or under the jack during use.
DO NOT
raise or lower vehicle lifting platform whilst the transmission jack is being used.
DO NOT
transport the jack, with or without a load, with the saddle in the raised position.
DO NOT
get jack wet or use in damp or wet locations or areas where there is condensation.
DO NOT
operate the jack when you are tired, under the influence of alcohol, drugs or intoxicating medication.
DO NOT
lift or support vehicles with jack and do not use jack as a load sustaining device.
DO NOT
use jack for any purpose other than removal, transportation, installation of transmissions.
DO NOT
move jack without suitable restraint on the load.
DO NOT
make any modifications to the jack, and DO NOT adjust or tamper with safety valve.
DO NOT
remove any labels from the jack. If labels are damaged or unclear replace them.
Use a qualified person to lubricate and maintain the jack.
DO NOT
use brake fluid to top up hydraulic unit. Use Sealey hydraulic oil only.
(Part No: HJO500MLS or HJO5LS)
Before storing in safe area, ensure all parts are clean, free of grease and oil (especially saddle).
Lower saddle to the lowest position.
INSTRUcTION MANUAL fOR:
VERTICAL TRANSMISSION JACK
MODEL NO's:
300etj.V2 & 500etj.
V2
Thank you for purchasing a Sealey product. Manufactured to a high standard this product will, if used according to these instructions
and properly maintained, give you years of trouble free performance.
1. SAFETY INSTRUCTIONS
2. SPECIFICATIONS
MODEL 500ETJ.V2
Rated capacity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .500kg
Ram extensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
Minimum saddle height . . . . . . . . . . . . . . . . . . . . . . . . 1075mm
Maximum saddle height . . . . . . . . . . . . . . . . . . . . . . . 1895mm
Base size . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .535x585mm
fixed/Adjustable saddle . . . . . . . . . . . . . . . . . . . . . . . . . . . fixed
Optional adjustable gearbox support . . . . . . . . . . . . . . . . ADT7
MODEL 300ETJ.V2
Rated capacity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .300kg
Ram extensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
Minimum saddle height . . . . . . . . . . . . . . . . . . . . . . . . 1075mm
Maximum saddle height . . . . . . . . . . . . . . . . . . . . . . . 1895mm
Base size . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .535x585mm
fixed/Adjustable saddle . . . . . . . . . . . . . . . . . . . . . . . . . . . fixed
Optional adjustable gearbox support . . . . . . . . . . . . . . . . . ADT7
3. ASSEMBLY
Unpack the product and check contents. Should there be any damaged or missing parts contact
your supplier immediately.
3.1.
Assemble wheels as in figure 1, for both sides of the jack base.
3.2.
Screw legs to base of the stand and check that the stand is at a right angle to a horizontal
plane, then tighten the leg screws.
3.3.
Place the saddle on the end of the hydraulic ram.
3.4.
Loosen the operating plug at the top of the hydraulic ram.
3.5.
The transmission jack is now ready for use.
fig 1
IMpORTANT:
PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS AND
CAUTIONS. USE THIS PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY
CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. PLEASE KEEP INSTRUCTIONS SAFE FOR FUTURE USE.
Original Language Version
300ETJ.V2, 500ETJ.V2 Issue: 1 - 25/06/12
Manufactured to exacting standards and suitable for general workshop applications. Model features dead man's handle for added safety and
strong construction for durability. Can be fitted with Adjustable Gearbox Support - check specification table.
© Jack Sealey Limited
