SeaLevel 7204e Скачать руководство пользователя страница 32

 

32 

© Sealevel Systems, Inc.  7204e Manual   |   SL9244  11/2022 

Appendix C – Electrical Interface 

RS-422 

The RS-422 specification defines the electrical characteristics of balanced voltage digital interface circuits. 
RS-422 is a differential interface that defines voltage levels and driver/receiver electrical specifications. On 
a differential interface, logic levels are defined by the difference in voltage between a pair of outputs or 
inputs. In contrast, a single ended interface, for example RS-232, defines the logic levels as the difference 
in voltage between a single signal and a common ground connection. Differential interfaces are typically 
more immune to noise or voltage spikes that may occur on the communication lines. Differential interfaces 
also have greater drive capabilities that allow for longer cable lengths. RS-422 is rated up to 10 Megabits 
per second and can have cabling 4000 feet long. RS-422 also defines driver and receiver electrical 
characteristics that will allow 1 driver and up to 32 receivers on the line at once. RS-422 signal levels range 
from 0 to +5 volts. RS-422 does not define a physical connector.

 

 

RS-485 

RS-485 is backwardly compatible with RS-422; however, it is optimized for party line or multi-drop 
applications. The output of the RS-422/485 driver is capable of being Active (enabled) or Tri-State 
(disabled). This capability allows multiple ports to be connected in a multi-drop bus and selectively polled. 
RS-485 allows cable lengths up to 4000 feet and data rates up to 10 Megabits per second. The signal levels 
for RS-485 are the same as those defined by RS-422. RS-485 has electrical characteristics that allow for 32 
drivers and 32 receivers to be connected to one line. This interface is ideal for multi-drop or network 
environments. RS-485 tri-state driver (not dual-state) will allow the electrical presence of the driver to be 
removed from the line. Only one driver may be active at a time and the other driver(s) must be tri-stated. 

 

Содержание 7204e




































Отзывы: