background image

Seagate Kinetic HDD Product Manual, Rev. B

 12

  

2.9

R

ELIABILITY

2.9.1

Annualized Failure Rate (AFR) and Mean Time Between Failures (MTBF)

The product shall achieve an Annualized Failure Rate (AFR) of 1.1% (MTBF of 800 thousand hours) when operated
a  nominal power and typical case temperatures of 40°C. Operation at temperatures outside the specifications in Section
2.8 may

 

increase the product AFR (decrease MTBF). AFR and MTBF are population statistics that are not relevant to

individual units.

AFR and MTBF specifications are based on the following assumptions for business critical storage system environments:

• 8760 power-on-hours per year.
• Operations at nominal voltages.
• Temperatures outside the specifications in Section 2.8 may reduce the product reliability.
• A workload rate below the average annualized specified limits. Operation at excessive I/O duty cycle may degrade

product reliability. 

• The enterprise application environment of power-on-hours, temperature, and I/O duty cycle effects the product

AFR and MTBF.

Table 11:   AFR and MTBF Specifications

Nonrecoverable read errors

1 per 1014 bits read, max

Annualized Failure Rate 

1.1%  (nominal power, 40°C case temperature)

Load unload cycles

300,000 cycles

Rated Workload

Average rate of <180TB/year
The MTBF specification for the drive assumes the I/O workload does not exceed the 

Average  Annualized Workload Rate Limit of <180TB/year. Workloads exceeding the 

annualized rate may  degrade the drive MTBF and impact product reliability. The Average 

Annualized Workload Rate Limit  is in units of TB per year, or TB per 8760 power on hours. 

Workload Rate = TB transferred x (8760 / recorded power on hours).

Warranty

To determine the warranty for a specific drive, use a web browser to access the following 

web page: 

http://www.seagate.com/support/warranty-and-replacements/

.

From this page, click on the “Check to see if the drive is under Warranty” link. The following 

are required to be provided: the drive serial number, model number (or part number) and 

country of purchase.The system will display the warranty information for the drive.

Preventive maintenance

None required.

Содержание ST4000NK001 Kinetic


























Отзывы: