Seagate Elite 9 Скачать руководство пользователя страница 17

Страница: 17 / 82

Elite 9 Product Manual, Rev. C

4.0

Standard features

Elite 9 drives have the following standard features:

• Integrated SCSI controller

• Single-ended or differential SCSI drivers and receivers

• Non-shielded 50-pin connector

• Initiator/target terminator power option

• SCSI bus parity with full parity pass-through

• SCSI disconnect/reconnect support

• Multiple SCSI initiator support

• SCSI-2 command set support

• Synchronous SCSI bus data transfer protocol (maximum offset of 15)

• 10.0 Mbytes/sec SCSI bus transfers (minimum period 100 nsec)

• 20.0 Mbytes/sec SCSI bus wide transfers (ST410800W/WD models)

• 954 Kbyte data buffer

• Cache buffer management

• User-selectable logical block size (180 to 4,096 bytes)

at even-number intervals

• ECC (error correction code) on the fly

• User-selectable automatic defect reallocation scheme

• User-selectable number of spare sectors per cylinder

• Industry standard 5.25-inch full-high form factor dimensions

(3.25 high

5.75 wide

8.00 deep)

• Microcode downloadable using the Write Data Buffer command

• Asynchronous and synchronous data-transfer protocols

• Firmware downloadable using a SCSI interface

• Programmable sector-reallocation scheme

• Flawed sector reallocation at format time

• Programmable auto-write and auto-read reallocation

• Reallocation of defects on command (Reassign Block command)

• 96-bit and Reed-Solomon error correction code

• Sealed head and disc assembly (HDA)

• No preventive maintenance or adjustments required

• Dedicated head-landing zone

• Automatic shipping lock

• Automatic thermal compensation

• Embedded Grey Code track address to eliminate seek errors

• Self-diagnostics performed at power-on

• 1:1 interleave

• Zone bit recording (ZBR)

• Vertical, horizontal, or top-down mounting

• Dynamic spindle brake

• Active internal termination (ST410800N/W models)

Содержание Elite 9



















































































Результаты поиска

Содержание Elite 9

Отзывы:

Похожие инструкции для Elite 9

Бренды по названию

Популярные бренды

Seagate Elite 9, Руководство по эксплуатации продукта

Результаты поиска

Содержание Elite 9

Отзывы:

Похожие инструкции для Elite 9

Бренды по названию

Популярные бренды