SeaDoo Rotax 1503 4-Tec 2005 Скачать руководство пользователя страница 86

Страница: 86 / 124

Section 01 ENGINES (1503 4-TEC)

Subsection 06 (CYLINDER HEAD)

Inspection

Check each lobe and bearing journal of camshaft
for scoring, scuffing, cracks or other signs of wear.

Measure camshaft bearing journal diameter and
lobe height using a micrometer.

Measure

clearance

between

both

ends

camshaft and cylinder head.

R1503motr102A

C A B

A. Camshaft lobe (exhaust valves)
B. Camshaft lobe (intake valves)
C. Camshaft bearing journal
D. Camshaft bearing journal — engine front

CAMSHAFT LOBE — EXHAUST VALVE

NEW MINIMUM

31.699 mm (1.248 in)

NEW MAXIMUM

31.809 mm (1.252 in)

SERVICE LIMIT

31.670 mm (1.247 in)

CAMSHAFT LOBE — INTAKE VALVE

NEW MINIMUM

31.480 mm (1.239 in)

NEW MAXIMUM

31.590 mm (1.244 in)

SERVICE LIMIT

31.450 mm (1.238 in)

CAMSHAFT BEARING JOURNAL

NEW MINIMUM

39.892 mm (1.5705 in)

NEW MAXIMUM

39.905 mm (1.5711 in)

SERVICE LIMIT

39.860 mm (1.5693 in)

CAMSHAFT BEARING JOURNAL —

ENGINE FRONT

NEW MINIMUM

24.939 mm (.9818 in)

NEW MAXIMUM

24.960 mm (.9826 in)

SERVICE LIMIT

24.910 mm (.9807 in)

CAMSHAFT BORE MEASURED IN DIAMETER

NEW MINIMUM

40.000 mm (1.5748 in)

NEW MAXIMUM

40.016 mm (1.5754 in)

SERVICE LIMIT

40.050 mm (1.5767 in)

CAMSHAFT BORE — ENGINE FRONT

MEASURED IN DIAMETER

NEW MINIMUM

25.000 mm (.9842 in)

NEW MAXIMUM

25.013 mm (.9848 in)

SERVICE LIMIT

25.050 mm (.9862 in)

Replace parts that are not within specifications.

Installation

For installation, reverse the removal procedure.
Pay attention to the following details.

Grease the camshaft bearing journals well by us-
ing the Klueber Isoflex grease (P/N 293 550 021)
or a similar product.

Install camshaft then place the camshaft lock

no. 20

in the slot.

R1503motr101B

1. Camshaft lock position

For other parts, refer to proper installation proce-
dure.

VALVE SPRING

Removal

Remove:
– rocker arms
– cylinder head.

Compress valve springs

no. 22

and

no. 23

. Use

valve spring compressor clamp (P/N 529 035 724)
and valve spring compressor cup (P/N 529 035
725).

smr2005-036

www.SeaDooManuals.net

Содержание Rotax 1503 4-Tec 2005





























































































































Результаты поиска

Содержание Rotax 1503 4-Tec 2005

Отзывы:

Похожие инструкции для Rotax 1503 4-Tec 2005

Бренды по названию

Популярные бренды

SeaDoo Rotax 1503 4-Tec 2005, Руководство по ремонту двигателя

Результаты поиска

Содержание Rotax 1503 4-Tec 2005

Отзывы:

Похожие инструкции для Rotax 1503 4-Tec 2005

Бренды по названию

Популярные бренды