SeaDoo Rotax 1503 4-Tec 2005 Скачать руководство пользователя страница 81

Страница: 81 / 124

Section 01 ENGINES (1503 4-TEC)

Subsection 06 (CYLINDER HEAD)

Measure rocker arm shaft diameter.

ROCKER ARM SHAFT DIAMETER

NEW MINIMUM

19.980 mm (.7866 in)

NEW MAXIMUM

19.993 mm (.7871 in)

SERVICE LIMIT

19.965 mm (.7860 in)

R1503motr90A

A. Measure rocker arm shaft diameter here

Any area worn excessively will require parts re-
placement.

Installation

For installation, reverse the removal procedure.
Pay attention to the following details.

Apply engine oil on rocker arm shaft.

IMPORTANT:

The rocker arm shaft can only be in-

stalled in one specific position. Therefore crank-
shaft as well as camshaft has to be positioned
with their locking pins when the piston of cylin-
der

no. 3

is on ignition TDC. Refer to CYLINDER

BLOCK section for crankshaft and the following
for the camshaft locking.

Use camshaft locking tool (P/N 529 035 839).
Rotate camshaft so that tool can be pushed in
camshaft hole and lock camshaft in place.

529035839

R1503motr111A

1. Camshaft locking tool

Then, the camshaft sprocket lines should be lined
up as shown in the following illustration.

R1503motr95A

1. Position lines

Position the rocker arm shaft with the notches on
top.

smr2005-036

www.SeaDooManuals.net

Содержание Rotax 1503 4-Tec 2005





























































































































Результаты поиска

Содержание Rotax 1503 4-Tec 2005

Отзывы:

Похожие инструкции для Rotax 1503 4-Tec 2005

Бренды по названию

Популярные бренды

SeaDoo Rotax 1503 4-Tec 2005, Руководство по ремонту двигателя

Результаты поиска

Содержание Rotax 1503 4-Tec 2005

Отзывы:

Похожие инструкции для Rotax 1503 4-Tec 2005

Бренды по названию

Популярные бренды