SeaDoo Rotax 1503 4-Tec 2005 Скачать руководство пользователя страница 34 | Manualshive

Страница: 34 / 124

SeaDoo Rotax 1503 4-Tec 2005 Скачать руководство пользователя страница 34

Section 01 ENGINES (1503 4-TEC)

Subsection 02 (INTAKE MANIFOLD AND SUPERCHARGER)

1

F00B2HA

2

1. Supercharger shaft
2. Distance sleeve

Apply engine oil on seal and push into retaining
disc by hand.

NOTE:

Always use a new oil seal when assem-

bling the supercharger.

1

R1503motr242A

1. Oil seal

Install step collar, O-ring, supercharger impeller
and washer on supercharger shaft. Apply Loctite
243 (P/N 293 800 060) on cap nut and temporary
finger tight cap nut.

NOTE:

The cap nut on the supercharger shaft has

a left-handed thread. The Loctite has to be applied
in a small dose into the nut.

4

R1503motr229B

3

2

1

5

1. Step collar
2. O-ring
3. Supercharger impeller
4. Washer
5. Cap nut

Complete installation of supercharger shaft, en-
gine side as follows:

CAUTION:

It is of the utmost importance that

all parts be absolutely clean. The compressor
shaft spins at up to 45 000 RPM and any debris
could cause a failure.

Install the first ceramic washer.

NOTE:

The ceramic washers differ in their inner

diameter. Install first the ceramic washer with the
bigger inner diameter. The ceramic washer with
the smaller inner diameter will be installed on the
lock washer side.

CAUTION:

Manipulate ceramic washers with

care, those parts are fragile.

IMPORTANT:

Apply

Kluber

Isoflex

grease

(P/N 293 550 021) to the inner diameter of
the gear thrust surface on the shaft, ceramic
washers, needle bearings shaft surface and lock
washer.

CAUTION:

No other grease can be used, other-

wise damage to bearings will occur.

Install the 40 needle bearings on the compressor
shaft.

NOTE:

The 40 needle bearings comes in a wax

strip with an adhesive backing.

Remove the adhesive backing.

Install the drive gear over the needle bearings.

Install the other ceramic washer (ceramic washer
with smaller inner diameter).

24

SMR2005-033

www.SeaDooManuals.net

«
...
32
33
34
35
36
...
»

Содержание Rotax 1503 4-Tec 2005





























































































































Отзывы:

Нет отзывов