SeaDoo Rotax 1503 4-Tec 2005 Скачать руководство пользователя страница 30

Страница: 30 / 124

Section 01 ENGINES (1503 4-TEC)

Subsection 02 (INTAKE MANIFOLD AND SUPERCHARGER)

F00B2DA

1. Supercharger shaft
2. Ball bearing
3. Retaining key

Screw out retaining disc with seal from hous-
ing half (engine side) by using the 4-pin socket
(P/N 529 035 948).

529035948

NOTE:

It may be necessary to heat the housing

with a heat gun to release the retaining disc.

F00B2AA

1. 4-pin socket

Remove ball bearing from supercharger housing
half (engine side) by using a press and a suitable
bearing pusher.

R1503motr236A

1. Supercharger housing half (engine side)
2. Bearing pusher

INSPECTION (PARTS
DISASSEMBLED)

Supercharged Clutch Components
and Gear

Replace worn parts by new ones. A clutch repair
kit is available. If all parts are within specifications,
replace the 40 needle bearings and spring washer
package on supercharger shaft.

NOTE:

Ceramic washers are not affected by wear.

Check the wear limit on drive gear, lock wash-
er and driven plate on supercharger shaft. Check
drive gear for cracks.

R1503motr360A

A. Driven plate thickness
B. Drive gear thickness
C. Lock washer thickness

SMR2005-033

www.SeaDooManuals.net

Содержание Rotax 1503 4-Tec 2005





























































































































Результаты поиска

Содержание Rotax 1503 4-Tec 2005

Отзывы:

SeaDoo Rotax 1503 4-Tec 2005, Руководство по ремонту двигателя, Страница: 30 / 124

Результаты поиска

Содержание Rotax 1503 4-Tec 2005

Отзывы: