background image

International registered trademark n. 2.777.971

IMPORTANT SAFETY INFORMATION

All the above described operations must be made exclusively by an authorized installer

Clean and grease parts in movement (wheels, 
counter-connecting rod, release, etc.)
Check for corroded parts and replace if 
necessary
Check if the screws and all mounting 
hardwares are properly tighten

Annual

Annual

Annual

Check the conditions of wear and tear of the 
devices in movement

Check the correct drain of the rainwater

Check the integrity of the connection cables

Annual

Annual

Annual

Inspect the track for any signs of cracking or 
separation

Ensure that the gate moves freely

Annual

Annual

Check and confirm the proper operation of all 
safety devices (photocells, edge sensors etc)
Check and confirm the operation of all 
installed accessories 
Check and confirm the operation of the 
manual release

Annual

Annual

Annual

TURNING ON THE POWER

Check the battery conditions and be sure that 
connections are free of corrosion
Verify the functionally of the battery backup, 
or power failure option

BY MAIN POWER SOURCE TURNED OF

Annual

TURNING OFF THE POWER

C

C

C

C

GENERAL SAFETY PRECAUTIONS

The following precautions are an integral and essential part of the product and must be supplied to the user Read 
them carefully as they contain important indications for the safe installation, use and maintenance.

1. These instruction must be kept and forwarded to all possible future users of the system.
2. This product must be used only for that which it has been expressly designed.
3. Any other use is to be considered improper and therefore dangerous.
4. The manufacturer cannot be held responsible for possible damage caused by improper, erroneous or 
    unreasonable use.
5. Avoid operating in the proximity of the hinges or moving mechanical parts.
6. Do not enter the path of the moving gate while in motion.
7. Do not obstruct the motion of the gate as this may cause a situation of danger.
8. Do not allow children to play or stay within the path of the moving gate.
9. Keep remote control or any other control devices out of the reach of children, in order to avoid possible involuntary 
    activation of the gate operator.
10. In case of break down or malfunctioning of the product, disconnect from the main power source. 
      Do not attempt to repair or intervene directly, contact only qualified personnel for repair.
11. Failure to comply with the above may create a situation of danger.
12. All cleaning, maintenance or repair work must be carried out by qualified personnel.
13. In order to guarantee that the system works efficiently and correctly it is important to have the manufacturer's  
      instructions on maintenance of the gate and operator carried out by qualified personnel.
14. In particular, regular checks are recommended in order to verify that the safety devices are operating correctly.

All installation, maintenance and repair work must be documented and made available to the user.

IMPORTANT SAFETY INSTRUCTIONS

         WARNING – To reduce the risk of injury or death:

1. READ AND FOLLOW ALL INSTRUCTIONS.
2. Never let children operate or play with gate controls. Keep the remote control away from children.
3. Always keep people and objects away from the gate. 

NO ONE SHOULD CROSS THE PATH OF THE MOVING  GATE.

4.Test the gate operator monthly. The gate MUST reverse on contact with a rigid object or stop when an object 
activates the non-contact sensors. After adjusting the force or the limit of travel, retest the gate operator. Failure to 
adjust and retest the gate operator properly can increase the risk of injury or death.
5. Use the emergency release only when the gate is not moving
6.  KEEP  GATES  PROPERLY  MAINTAINED.  Read  the  owner’s  manual.  Have  a  qualified  service  person  make 
repairs to gate hardware.
7. The entrance is for vehicles only. Pedestrians must use separate entrance.
8. Every gate operator installation MUST have secondary protection devices agains entrapments, such as edge 
sensors and photo beams more in particulary in places where the risk of entrapments is more likely to occur 
9. SAVE THESE INSTRUCTIONS

!

PERIODICAL MAINTENANCE

Содержание SUPER FULL TANK 500 G6 120V





















Отзывы: