STORAGE AND PRESEASON PREPARATION
Storage
WARNING
Because
fuel
and
oil
are
flammable,
you
should
have
an authorized Sea-Doo dealer,
repair shop, or person of your
own choosing to inspect the fuel
system integrity as specified in the
periodic inspection chart.
It is recommended that the watercraft
be serviced by an authorized Sea-Doo
dealer, repair shop, or person of your
own choosing for storage, however
the following operations can be per-
formed by you with a minimum of
tools.
NOTE:
Carry out the following tasks in
the same order as detailed in this sec-
tion.
NOTICE
Do not run the engine dur-
ing the storage period.
Propulsion System
Jet Pump Cleaning
Clean jet pump by spraying water in
its inlet and outlet and then apply a
coat of LUB. & ANTI-CORROSIVE
(293600016) (P/N 779168) or equiv-
alent.
WARNING
Always remove tether cord from
the engine cut-off switch to pre-
vent unexpected engine starting
before cleaning the propulsion
system components. Engine must
not be running for this operation.
Jet Pump Inspection
See your authorized Sea-Doo dealer.
Fuel System
Fuel System Protection
FUEL
STABILIZER
(413408601)
(P/N 779171) (or equivalent) should be
added in the fuel tank to prevent fuel
deterioration and fuel system gum-
ming. Follow stabilizer manufacturers'
instructions for proper use.
NOTICE
It is highly recommended
to add fuel stabilizer at storage in or-
der to maintain fuel system in good
condition.
Fuel stabilizer should
be added prior to engine lubrica-
tion and fuel tank top up to ensure
fuel system components protection
against varnish deposits.
Fill up fuel tank completely as ex-
plained in
FUELING
subsection. Make
sure there is no water inside fuel tank.
NOTICE
Should
any
water
be
trapped inside fuel tank, severe in-
ternal damage will occur to the fuel
injection system.
Engine and Exhaust Systems
Exhaust System Flushing
Perform procedure as described in
MAINTENANCE PROCEDURES
.
Engine Oil and Filter Replacement
The oil change and filter replacement
may be performed by an authorized
Sea-Doo dealer, repair shop, or person
of your own choosing.
Exhaust System Draining
In areas where temperature may
freeze, water trapped in the exhaust
system must be removed.
Using the flushing connector located
on the port (LH) side of the stern, inject
pressurized air at 379 kPa (55 PSI) into
system until there is no more water
flowing from jet pump.
______________
111
Содержание SAR 2018 Series
