Sea-doo GS 5644 Скачать руководство пользователя страница 37

Страница: 37 / 107

All Models Except XP

The basket is provided with a holder to
store an approved fire extinguisher.
Fire extinguisher (sold separately)
should not be loose in the front stor-
age compartment. A second holder
contains the

Operator’s Guide

Safety

Handbook

and a tool kit. It can be used

to carry personal articles.

TYPICAL

Step

: Turn cover counterclockwise

Step

: Lift

1. Holder

XP Models

The basket is provided with separate
compartments.

1. Fire extinguisher (sold separately)
2. Retaining strap

18) Front Storage

Compartment Cover
Latch

Pull the latch lever upward in order to
open the front storage compartment
cover. Always relatch.

NOTE:

Verify periodically the lock pin

tightness of storage cover. Tighten if
needed and make sure storage cover
latches properly.

19) Front Storage

Compartment Cover
Hinge/Locking
Mechanism

GS and GSX RFI Models

Hinge is provided with a locking mech-
anism to hold front storage compart-
ment cover when fully open. To close
cover, pull tab.

GTS Models

Hinge is provided with a locking mech-
anism to hold front storage compart-
ment cover when fully open. To close
cover, pull side pins.

20) Front Storage

Compartment Cover
Lock (if so equipped)

A convenient lock is provided to pro-
tect personal articles when the water-
craft is unattended.

TYPICAL

1. Safety lock

F04L0PY

1
2

F08L0UY

F07L1IY

smo2000-002a.book Page 35 Tuesday, September 28, 1999 12:00 PM

www.SeaDooManuals.net

Содержание GS 5644












































































































Результаты поиска

Содержание GS 5644

Отзывы:

Бренды по названию

Популярные бренды

Sea-doo GS 5644, Руководство оператора

Результаты поиска

Содержание GS 5644

Отзывы:

Бренды по названию

Популярные бренды