Sea-doo 2004 GTI Скачать руководство пользователя страница 103 | Manualshive

Страница: 103 / 130

background image

103

TROUBLESHOOTING

The following chart is provided to help in diagnosing the probable source of simple
troubles. You may be able to solve many of these problems rather quickly, but
others may require the skills of a mechanical technician. In such cases, consult
an authorized SEA-DOO dealer for servicing.

Monitoring Beeper Coded Signals

CODED SIGNALS

POSSIBLE CAUSE

REMEDY

2 short beeps
(while installing safety
lanyard on post).

• Confirms safety lanyard signal

operation.

Engine can be started.

1 long beep
(while installing safety
lanyard on watercraft post

• Bad connection.

Reinstall safety lanyard cap cor-
rectly over post.

• Wrong safety lanyard.

Use a safety lanyard that has been
programmed for the watercraft.

• Defective safety lanyard.

Use another programmed safety
lanyard.

• Dried salt water in safety lanyard

cap.

Clean safety lanyard cap to re-
move salt water.

• Improper operation of MPEM or

defective wiring harness.

Refer to an authorized SEA-DOO
dealer.

1 second beep every second
intervals

(DI models)

.

• Engine drowned mode is active. Release throttle to cancel this

mode.

A 2 seconds beep every
minute intervals

(RFI models)

.

• Fuel tank level is low.

Refill.

4 short beeps every
3 seconds interval
for 2 hours.

• Safety lanyard has been left on

its post without starting engine
or after engine was stopped.

To prevent battery discharge,
remove the safety lanyard from
its post.

A 2 seconds beep every
2 seconds intervals

(DI models)

.

• Exhaust system overheat.

See engine OVERHEATING.

A 2 seconds beep every
minute intervals

(DI models)

.

• Fuel tank level is low.

Refill as soon as possible.

• Very low battery voltage.

Refer to an authorized SEA-DOO
dealer.

• Coolant and exhaust gas temper-

ature sensors or TPS (throttle po-
sition sensor) or CPS (crankshaft
position sensor) malfunction.

Refer to an authorized SEA-DOO
dealer.

• MPEM malfunction.

Refer to an authorized SEA-DOO
dealer.

A 2 seconds beep every
15 minutes intervals

(DI models)

.

• Oil injection reservoir level is

low.

Refill.

Continuous beep.

• Engine overheats.

See engine OVERHEATING.

smo2004-002a.book Page 103 Thursday, August 21, 2003 2:54 PM

www.SeaDooManuals.net

«
...
101
102
103
104
105
...
»

Содержание 2004 GTI



































































































































Отзывы:

Нет отзывов

Похожие инструкции для 2004 GTI

Бренд: Zodiac Страницы: 55

Бренд: Walker Bay Страницы: 18

CAP CAMARAT 7.5 CC serie 2

Бренд: Jeanneau Страницы: 112

SEA-DOO GTI 130 2019

Бренд: BRP Страницы: 204

Бренд: Feathercraft Страницы: 8

Cross 75 Bow Rider

Бренд: YAMARIN Страницы: 42

Бренд: YAMARIN Страницы: 53

Бренд: Lifetime Страницы: 9

Бренд: Supra Страницы: 74

Бренд: Supra Страницы: 72

Бренд: Sea-doo Страницы: 130

Бренд: Sea-doo Страницы: 138

Бренд: Sea-doo Страницы: 144

Бренд: X-TREME scooter Страницы: 30

Бренд: LaserPerformance Страницы: 10

Бренд: LaserPerformance Страницы: 15

Бренд: LaserPerformance Страницы: 11

Бренд: Hunter Страницы: 28

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды