manualshive.com logo in svg

Sea-doo 2003 LRV DI, Руководство оператора, Страница: 8 / 88

Поделиться
Скачать
Sea-doo 2003 LRV DI Скачать руководство пользователя страница 8

6

 SAFETY MEASURES

General

To fully appreciate the pleasures,
enjoyment and excitement of boat-
ing there are some basic rules that
should be observed and followed by
any rider. Some rules may be new
to you or covered in the 

Sea-Doo

Safety Handbook

 or 

Safety Video-

cassette

, others may be common

sense or obvious… irrespective, we
ask that you please take a few min-
utes of your time to read these safe-
ty instructions completely together
with your safety handbook and any
supplement applicable to your mod-
el before you operate your water-
craft. 

Failure to follow this safety

information and safe boating rules
could result in injury, including the
possibility of death to you, your
passenger(s), or other water users.

Bombardier recommends not to oper-
ate a watercraft under 16 years of
age.

Become completely familiar with the
controls and operation of the water-
craft before embarking on your first
trip or taking on a passenger(s). If you
have not had the opportunity to do so
with your authorized Sea-Doo dealer,
practice driving solo in a suitable area
and feel the response of each con-
trol. Be fully familiar with all controls
before applying throttle above idle
speed. As its operator, you control
and are responsible for the water-
craft’s safe operation.

Always carry the regulatory required
safety items on board. Check the lo-
cal regulations or consult your au-
thorized Sea-Doo dealer.

Make sure that all users of the wa-
tercraft read and understand all on-
product warnings.

Operation

Always perform the pre-operation
checks as specified in this guide. 

Operator and passenger(s) should at
all times wear a coast guard approved
personal flotation device (PFD) that is
suitable for personal watercraft.

Operator and passenger(s) should
wear protective clothing. Severe in-
ternal injuries can occur if water is
forced into body cavities of males or
females as a result of falling into wa-
ter or being near jet thrust nozzle. Wet
suit bottom (or thick, tightly woven,
snug fitting clothing that provides
equivalent protection. Thin bike shorts
for example would not be appropriate),
footwear, gloves and goggles/glasses
are recommended.

Always keep in mind that as the
throttle lever is released to idle posi-
tion, less directional control is avail-
able. 

To turn the watercraft, both

steering and throttle are neces-
sary.

Like any other craft, this watercraft
has no brake. Stopping distance will
vary depending on initial speed, load,
wind, and water conditions. Practice
stopping and docking in a safe, traffic
free area to have an idea of how long
it will take to stop the watercraft un-
der varying conditions. Do not re-
lease throttle when trying to steer
away from objects. You need throttle
to steer. Do not use the watercraft’s
reverse, if so equipped, to stop.

Ensure that all passengers know
how to swim and how to reboard
the watercraft from the water. 

The operator and passenger(s) should
be properly seated and wearing an
approved PFD before starting or
moving the watercraft, and at all
times when watercraft is in motion. 

smo2003-005a.book  Page 6  Friday, November 1, 2002  8:25 AM

Содержание 2003 LRV DI

























































































Отзывы:

Нет отзывов