manualshive.com logo in svg

Sea-Bird Scientific SBE 25plus, Руководство пользователя

Поделиться
Скачать
Sea-Bird Scientific SBE 25plus Скачать руководство пользователя страница 41

1.

Put the system in its deployment position, either vertical or horizontal.

2.

Use the software to set the pressure offset to 0.0.

3.

Collect data and show the pressure sensor output in decibars.

4.

Compare the pressure sensor output to a good quality barometer at the same
elevation.

5.

Calculate the offset. Offset = barometer value - 9plus output.

6.

Enter this value in the .xmlcon or .con file.

Example offset correction:

Absolute pressure as measured by a barometer = 1010.5 mbar. 1010.5 × 0.01=
10.1050 dbars.
Pressure value from the sensor = -2.5 dbars.
Seasave software output value (gauge pressure) = 14.7 psi.
The software converts psia to decibars: Decibars = (psia - 14.7) × 0.
Convert the 9plus from gauge to absolute: add 14.7 psia:
-2.5 dbars + (14.7 psi × 0.689476dbar/psia) = -2.5 + 10.13 - 7.635 dbars.
Offset = 10.1050 - 7.635 = 2.47 dbars. Enter this value in the .xmlcon or .con file.

Use a dead-weight pressure generator to calculate slop and offset values

1.

Remove the nylon fitting from the 9plus. There is silicon oil in the fitting and some
may spill.

2.

Use a fitting with an O-ring face seal such as Swagelok 200-1-OR as a connector.
The bore in the end flange is 5/16-24 straight thread.

3.

Use the software to set the pressure slope to 1.0 and the pressure offset to 0.0 in
the .xmlcom or .con files.

4.

Use different pressures with the dead-weight pressure generator and collect data with
the 9plus. Show the output in decibars.

5.

Do a linear regression on the data to calculate slope and offset.

6.

Enter the calculated values in the .xmlcon or .con configuration file.

7.

Fill the pressure port fitting with silicon oil from the manufacturer-supplied kit.

7.9.3 Temperature

The main cause of calibration drift in temperature sensors is the age of the thermistor
element. This drift is usually a few thousandths of a degree during the first year, and less
after that. Environmental conditions have little effect on temperature sensors.

7.10 Spare parts and accessories

23302C

SBE 25 stainless steel protective cage, no mounts

50586 

SBE 25 stainless steel protective cage, 23301C, with standard sensor mounts for 3F, 4C, 5, ECO,
Seapoint, for vertical deployment

50586.H

SBE 25 stainless steel protective cage, 23301C, with standard sensor mounts for 3F, 4C, 5, ECO,
Seapoint, for horizontal deployment. Mounted in SBE 32 CTD extension stand

50671 

Mount kit, 25plus housing to 25-type cage, 23303 

801206 

Data I/O cable, 2.4 m, DN 32366 

801421 

Data I/O cable, 20 m shielded, DN 32789 

20200.0 

USB-to-serial port adapter, FTDI UC232R-10 

50508 

SBE 25plus support kit—has spare communications cables, C, T sensor cable, pump-data Y-cable,
connectors, dummy plugs, maintenance supplies and other mechanical spares

171883 

Y-cable, pump-data I/O, DN 32896 

Maintenance

39

Содержание SBE 25plus



































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды