Se-Kure Controls LE PLUS страница 14 Скачать руководство пользователя

Страница: 14 / 19

Installation Instructions for the

Outdoor Product Alarm System

SK-903KB

Outdoor Product Alarm Module w/External Horn

SK-947KB8

Outdoor Cable (Available in Combinations of 8') - [xx = 8, 16, 24, etc.]

SK-907KB

Outdoor Product Alarm Splitter

SK-195

AC/DC Power Supply

SKP-416K

Security Screw Allen Wrench

SK-109KB

Terminator Loop

SK-109KB

Terminator Loop

SK-109KB

Terminator Loop

SK-947KB

Outdoor Cable

SK-947KB

Outdoor Cable

SK-903KB

Outdoor Product
Alarm w/Keypad &
External Horn

SK-195

AC/DC

Power supply

SK-907KB

Outdoor Splitter

Dry Contacts

(can handle up to 24v)

1 Amp

Ground (GREEN)

(connect eyelet to
center screw on
standard outlet plates)

Installation Instructions:

Special Note:

Make all connections before installing

batteries and connecting the AC/DC Power Supply.

Indoors:
1.

Screw the Alarm Module’s

Green Ground Wire

to the

ground screw located on the center of a grounded 110v AC
outlet cover plate, and plug the AC/DC Power Supply into
the outlet. (Hold off until the battery step to plug the Power
Supply into the Alarm Module).

Attach an (SK-947KB) Outdoor Cable to the end of the

Alarm Module Cable, and extend it Outdoors.

Outdoors:
3.

Connect the cable extending from indoors to the

(SK-907KB) Outdoor Splitter. (The Splitter can be mounted
to a wall with #10 screws).

Do not allow Splitter or Connectors
to remain in standing water.

Содержание LE PLUS




















Результаты поиска

Содержание LE PLUS

Отзывы:

Похожие инструкции для LE PLUS

Бренды по названию

Популярные бренды

Se-Kure Controls LE PLUS, Руководство по установке

Результаты поиска

Содержание LE PLUS

Отзывы:

Похожие инструкции для LE PLUS

Бренды по названию

Популярные бренды