SDC EntryCheck 920P Скачать руководство пользователя страница 1

The 

EntryCheck

™  920P Indoor/Outdoor Keypad is a surface-mount 

digital keyless entry system designed for access control applications.  
The backlit keys  are bright and easy-to-read. A heavy cast vandal 
resistant housing design with mounting plate allows the 920P  to be 
mounted on a  rugged surface or on a standard single-gang electrical 
box.  
  
The 920P has a capacity of 500 users. Users can be assigned to use 4 
to 6 digit  PIN codes and/or HID 125kHz proximity access credentials. An 
authenticated access can be programmed to activate one or both of the 
relay outputs. 

The timed “anti-passback” feature prevents using the same credentials  
twice  before a programmed waiting period has  elapsed.

Two long lasting solid state LED indicators show the status of the 
system.  The left bi-color indicator lights red to indicate power, then 
green when a relay is active (access grant, etc.).  The right indicator 
flashes yellow to indicate that the keypad is in programming mode.

An internal sounder can be programmed to beep each time a key is 
pressed or when an output is activated.  An internal jumper sets the 
sounder volume high or low.

The 

SENSE 

input can be configured one of two ways through 

programming .  When configured for “Door Sense”, the input is wired to a 
normally closed door position switch to detect when the door is opened 
or closed.  Forced entry or door ajar situations can then be detected. The 
“Auto-relock” feature can also be used to turn off the Main Relay output 
immediately when the door is closed after access has been granted to 
prevent “tailgating”.
When the 

SENSE 

input is configured for “Inhibit”, the input can be wired 

to a normally open “service” switch or automatic timer that will disable 
access while the switch is closed.

The 

REQUEST-TO-EXIT 

input can be wired to a normally open 

pushbutton to provide codeless activation of the Main Relay, Auxiliary 
Relay, Output #3 or Output #4 (programmable).

The 

ALARM SHUNT 

signal is available when access is granted.  This 

signal can be programmed to activate any of the relays or solid state 
outputs  to shunt alarm contacts on the access door/gate  preventing the  
triggering of an alarm when an authorized access occurs.

The 920P 

EntryCheck

™ is powered from a 12 or 24V AC or DC source. 

The non-volatile EEPROM memory retains  entry codes and 
programming when power is removed.  An internal jumper is provided to 
reset the master code.  The Main Relay has a 5 Amp capacity.  The 
Auxiliary Relay has a 2 Amp capacity.  Two solid state outputs, capable 
of sinking 100 mA to common are programmable for alarm shunting, or 
to signal forced entry, door ajar, keypad lockout, and keypad active 
conditions.

P:\INST INSTRUCTIONS\ACCESS CONTROLS\INST-920P       Rev K       08-21       Page 1

920P

EntryCheck 

TM

SPECIFICATIONS

Mechanical

Dimensions:  3.00" W x 5.75" H x 1.375" D

      (1.4375” wall projection)

Electrical

Input Voltage: 12/24 Volts AC or DC
Operating Current: 30 mA typical, 150 mA max

  Output Ratings

   Main Relay: Form “C” 5 Amps @ 28 Volts max

     Auxiliary Relay: Form “C” 2 Amp @ 28 Volts max

Type:  Solid state outputs (Outputs #3 & #4)
Short-to-common 100 mA @ 24 VDC maximum

Environmental

Temperature: -4°F to 140°F (-20°C to 60°C)
Humidity: 5% to 95% non-condensing

Features

Security Door Controls

 

4 to 6 digit user codes

 

4 independent outputs

 

4 independent timers

 

2 Form C relay contacts

 

2 solid state open collector outputs

 

Program entry codes to activate one or 
two relays

 

Disable input

 

Door sense input

 

Request-to-exit/Reception input

 

Keypad tamper lockout

 

Timed anti-passback

 

Anti-tailgate

 

Two LED status indicators

 

Tactile key feel

 

Audible code entry verification

 

12V or 24V, AC or DC operation

                                                                

 

Keypad programmable

 

500 user codes

 

3 User Modes 

PIN or Card
Card Only
Card and PIN

Any suggestions or comments to this instruction or 

product are welcome.  Please contact us through 

our website or email [email protected] 

SECURITY DOOR CONTROLS   ■   WWW.SDCSECURITY.COM

[t] 800.413.8783  ■  805.494.0622  ■  E-mail: [email protected]  ■  801 Avenida Acaso, Camarillo, CA  93012  ■  PO Box 3670, Camarillo, CA  93011

INSTALLATION INSTRUCTIONS

Содержание EntryCheck 920P









Отзывы: