Scotsman CMS1002R Скачать руководство пользователя страница 1

Страница: 1 / 27

INTRODUCTION

This manual is intended as a reference for the
installation and service of a Scotsman ice maker
model CMS1002.

This model is a remote condenser cuber, 30" wide
and should be connected to a Scotsman remote
condenser.

TABLE OF CONTENTS

Page

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Environmental Limitations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

For the Installer

Machine & Bin Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

For the Plumber . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Remote Condenser . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Coupling Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

For the Electrician

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Final Check List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Initial Start Up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Adjustments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Component Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Service Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Service Diagnosis

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Removal and Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Parts lists and wiring diagrams are in the center of this manual, printed on yellow paper.

CMS1002R

September, 1993

Page 1

Содержание CMS1002R




























Результаты поиска

Содержание CMS1002R

Отзывы:

Похожие инструкции для CMS1002R

Бренды по названию

Популярные бренды

Scotsman CMS1002R, Руководство пользователя

Результаты поиска

Содержание CMS1002R

Отзывы:

Похожие инструкции для CMS1002R

Бренды по названию

Популярные бренды