Scotsman AF300 Скачать руководство пользователя страница 1

Страница: 1 / 26

INTRODUCTION

To the owner or user: This service manual is
intended to provide you, and the maintenance or
service technician, with the information needed to
install, start up, clean, maintain and repair this
product.

The AF300 is an ice machine that produces flaked
ice and stores it in a insulated bin. It automatically
maintains the level of ice by turning on when the
ice level falls and switches off when it is full.

This unit in serviceable in place; the ice storage
bin and hood may be removed from the chassis to
allow service access without removing the ice
machine from its installed location. The
refrigeration system uses R-22 as the refrigerant.

Table of Contents

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 2

Limitations

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 3

Installation

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 4

Plumbing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 5

Final Check List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 6

Cabinet Removal

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 7

Component Location . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 8

Electrical Sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 9

Initial Start Up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 10

Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 11

Water Schematic

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 15

Refrigeration Schematic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 16

Technical Charateristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 17

Service Diagnosis

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 18

Removal and Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 20

Parts lists and wiring diagrams are located in
the center of this manual, printed on yellow
paper.

Keep this manual for reference.

This manual was printed on recycled paper.

AF300

Содержание AF300



























Результаты поиска

Содержание AF300

Отзывы:

Похожие инструкции для AF300

Бренды по названию

Популярные бренды

Scotsman AF300, Руководство пользователя

Результаты поиска

Содержание AF300

Отзывы:

Похожие инструкции для AF300

Бренды по названию

Популярные бренды