Read pages
1992-99 Pontiac Bonneville
3-7 for kit
assembly.
Radio Removal:
1. Using a panel removal tool/screwdriver, carefully release the fastening clips from around the perimeter of
the radio trim bezel and remove the panel.
2.
Extract the three screws securing the radio to the dash, pull the radio from the cavity, unplug all the
connectors and remove the radio.
LEFT SIDE
RIGHT SIDE
"B1" BRACKET USE HOLE #2
"A1" BRACKET USE HOLE #4
LADO IZQUIERDA
LADO DERECHO
"B1" SOPORTE
"A1" SOPORTE USA
USA ABERTURA NO. 2
ABERTURA NO. 4
FRONT OF KIT
"A2" BRACKET USE HOLE #2
FRENTE DE ESTUCHE
"A2" SOPORTE USA ABERTURA NO. 2
USE THE SHADED BRACKETS & THE INDICATED HOLE LOCATIONS. CUT OFF THE REMAINING BRACKETS AND DISCARD.
Usa los soportes asombrados y las localizaciónes de aberturas indicadas. Corta los soportes que sobran y desechalas.
Read pages
1987-91 Pontiac Bonneville
3-7 for kit
assembly.
Radio Removal:
1. Place the gear selector in low gear to gain clearance.
2. Gently pull on the edges of the radio panel to release the panel clips and remove the panel.
3. Remove the two screws from the bracket above the radio.
4. Remove one screw from the
SPACER
rear support bracket (access
"D2" BRACKET
ESPACIADOR
CUT OFF PINS (TWO SPACERS)
through the ashtray cavity).
USE HOLE #2
"D2" SOPORTE
CORTA LAS CLAVIJAS
USA ABERTURA NO. 2
5. Insert a thin blade screwdriver
(DOS ESPACIADORES)
into the two slots below the
radio and pry the metal
SPACER
ESPACIADOR
retaining tabs upward to release
"B2" BRACKET
them.
USE HOLE #2
6. Slide the radio out of the cavity,
"B2" SOPORTE
USA
ABERTURA
disconnect all the electrical
connections, then remove the radio.
TOP
NO. 2
TOPE
CUT OFF TABS
(TWO BRACKETS)
ROMPE LAS LENGUETAS
(DOS SOPORTES)
USE THE SHADED BRACKETS & THE INDICATED HOLE LOCATIONS. CUT OFF THE REMAINING BRACKETS AND DISCARD.
Usa los soportes asombrados y las localizaciónes de aberturas indicadas. Corta los soportes que sobran y desechalas.
Read pages
1984-88 Pontiac Fiero
3-7 for kit
assembly.
Radio Removal:
1. Remove the four screws from the radio trim panel.
2. Pull the panel up and outward toward the right.
3. Remove the four screws from the radio brackets and pull the radio out of the cavity.
4. Disconnect the antenna, speaker leads and all the electrical connections, then remove the radio.
LEFT SIDE
RIGHT SIDE
"B1" BRACKET USE HOLE #4
"A1" BRACKET USE HOLE #3
LADO IZQUIERDA
LADO DERECHO
"B1" SOPORTE
"A1" SOPORTE USA
USA ABERTURA
ABERTURA NO. 3
NO. 4
4
3
Read pages
1982-96 Oldsmobile Cutlass Ciera
3-7 for kit
assembly.
Radio Removal:
1. Remove the ashtray from the mounting bracket.
2. Extract the two screws from the padded portion of the dash in the ashtray location.
3. Remove the single screw from the trim ring below the steering column and remove the trim.
4. Remove the two screws from the top of the trim above the steering column and remove the trim.
5. Carefully pry out each A/C vent, one on each side of the steering column.
6. Remove the two screws from the left A/C vent location and one screw from the right A/C vent location.
7. Carefully pry out the padded portion of the dash trim.
8. Remove the four screws from inside the top edge of the instrument cluster trim and the four screws from
the bottom edge and remove the trim.
9. Remove the four screws from the radio bracket/dummy panel; pull the radio out of the cavity, disconnect
the antenna, speaker leads and all the electrical connections. Then remove the radio.
"D1" BRACKET USE HOLE #2
"D1" SOPORTE USA ABERTURA NO. 2
(FOUR BRACKETS) CUT OFF TABS
(4 SOPORTES) ROMPE EL LENGUENTE
TOP
TOPE
"C2" BRACKET
USE HOLE #5
"C2" SOPORTE
"C1" BRACKET
USA ABERTURA
USE HOLE #2
"C1" SOPORTE
USA
ABERTURA
NO. 2
NO. 5
BOTTOM
"D2" BRACKET USE HOLE #1
FONDO
"D2" SOPORTE USA ABERTURA NO. 1
USE THE SHADED BRACKETS & THE INDICATED HOLE LOCATIONS. CUT OFF THE REMAINING BRACKETS AND DISCARD.
Usa los soportes asombrados y las localizaciónes de aberturas indicadas. Corta los soportes que sobran y desechalas.
Read pages
1984-88 Oldsmobile Cutlass
3-7 for kit
assembly.
Supreme Classic
Radio Removal:
1. Carefully pry outward on each corner of the radio trim panel to release the spring clips.
2. Unscrew the cigarette lighter housing and remove the panel.
3. Remove the four screws from the radio mounting bracket and pull the unit out of the cavity. Disconnect
the antenna, speaker leads and all the electrical connections, then remove the radio.
"C2" BRACKET USE HOLE #3
"C2" SOPORTE USA
"A1" BRACKET USE HOLE #3
ABERTURA NO. 3
"A1" SOPORTE USA ABERTURA NO. 3
RIGHT SIDE
LEFT SIDE
LADO DERECHO
LADO IZQUIERDA
3
3
TRIM
BRACKET
3
3
"A2" BRACKET
CORTA EL
"B2" BRACKET
FRONT OF KIT
4
USE HOLE #3
3
SOPORTE
FRONT OF KIT
USE HOLE #3
FRENTE DE
"A2" SOPORTE
ESTUCHE
"D2" BRACKET
USA ABERTURA NO. 3
FRENTE DE ESTUCHE
"B2" SOPORTE
"C2" BRACKET USE HOLE #3
USA ABERTURA NO. 3
USE HOLE #4
"C2" SOPORTE USA ABERTURA NO. 3
"D2" SOPORTE USA ABERTURA NO. 4
USE THE SHADED BRACKETS & THE INDICATED HOLE LOCATIONS. CUT OFF THE REMAINING BRACKETS AND DISCARD.
USE THE SHADED BRACKETS & THE INDICATED HOLE LOCATIONS. CUT OFF THE REMAINING BRACKETS AND DISCARD.
Usa los soportes asombrados y las localizaciónes de aberturas indicadas. Corta los soportes que sobran y desechalas.
Usa los soportes asombrados y las localizaciónes de aberturas indicadas. Corta los soportes que sobran y desechalas.
28
25
