Read pages
1989-94 Oldsmobile Cutlass Supreme
3-7 for kit
assembly.
Radio Removal:
BOTTOM
1. Remove the five screws from the top underside of
FONDO
the radio/instrument trim panel. Carefully release
the clips from along the bottom edge of the panel
"C2" BRACKET
to remove it.
USE HOLE #6
"C2" SOPORTE USA
2. Remove the two screws securing the radio to the
ABERTURA NO. 6
dash, and pull the radio out of the cavity.
Disconnect the wire harnesses and the antenna
lead then remove the radio.
"B2" BRACKET
USE HOLE #6
"B2" SOPORTE USA
ABERTURA NO. 6
USE THE SHADED BRACKETS & THE INDICATED HOLE LOCATIONS. CUT OFF THE REMAINING BRACKETS AND DISCARD.
Usa los soportes asombrados y las localizaciónes de aberturas indicadas. Corta los soportes que sobran y desechalas.
Read pages
1986-88 Oldsmobile Delta 88
3-7 for kit
assembly.
1989-91 Oldsmobile Eighty-Eight Royale
1984-93 Oldsmobile Ninety-Eight
Radio Removal:
1. Place the gear shift lever in the D1 position. Pull the rubber steering column trim boot towards the rear of
the car.
2. Remove the four screws from the heater control/vent trim panel. Very carefully pull the entire trim panel
away from the dash and remove the trim panel.
3. Extract the single screw from each end of the padded radio trim panel.
4. Remove the four screws from the bottom of the radio/dash trim panel.
5. Extract the seven screws from the top of the radio/dash trim panel.
6. Unhook the ashtray/light wiring
RIGHT SIDE
terminal located
LADO IZQUIERDA
LEFT SIDE
LADO DERECHO
"D1" BRACKET
directly behind the
SPACER
"C1" BRACKET USE HOLE #4
SE HOLE #3
SPACER
EL ESPACIO
"C1" SOPORTE
"D1" SOPORTE USA
ashtray.
EL ESPACIO
USA ABERTURA NO. 4
ABERTURA NO. 3
7. Remove the trim panel.
7
7
8. Remove the four screws
which secure the radio to the
dash and slide the
radio out of the
SPACER
SPACER
EL ESPACIO
cavity. Disconnect
the antenna, speaker
leads and all the
5
FRONT OF KIT
4
electrical connections,
"C2" BRACKET
"D2" BRACKET
FRENTE DE
then remove the radio.
USE HOLE #4
USE HOLE #2
ESTUCHE
"C2" SOPORTE
"D2" SOPORTE USA ABERTURA NO. 2
USA ABERTURA NO. 4
USE THE SHADED BRACKETS & THE INDICATED HOLE LOCATIONS. CUT OFF THE REMAINING BRACKETS AND DISCARD.
Usa los soportes asombrados y las localizaciónes de aberturas indicadas. Corta los soportes que sobran y desechalas.
Read pages
1992-93 Oldsmobile Eighty-Eight Royale
3-7 for kit
assembly.
Radio Removal:
1. Extract the three screws securing the radio trim/dash bezel from above the instrument cluster and the
radio.
2. Remove the screws on each side of the steering column that secure the radio trim/dash bezel. Carefully
pull out on the bezel to remove it.
"D1" BRACKET USE HOLE #2
"D1" SOPORTE USA ABERTURA NO. 2
3. Extract the four screws securing the radio to the dash,
pull the radio from the cavity,
"B2" BRACKET USE HOLE #2
"B2" SOPORTE
USA ABERTURA NO. 2
unplug all the
connectors and
remove the
TOP
"A2" BRACKET
TOPE
radio.
USE HOLE #1
"A2" SOPORTE
USA ABERTURA
NO. 1
CUT OFF TAB
BOTTOM
(4 BRACKETS)
FONDO
ROMPE EL LENGUETE
(CUARTO SOPORTES)
"C2" BRACKET USE HOLE #1
"C2" SOPORTE USA ABERTURA NO. 1
USE THE SHADED BRACKETS & THE INDICATED HOLE LOCATIONS. CUT OFF THE REMAINING BRACKETS AND DISCARD.
Usa los soportes asombrados y las localizaciónes de aberturas indicadas. Corta los soportes que sobran y desechalas.
26
Read pages
1983-84 Oldsmobile Omega
3-7 for kit
assembly.
Radio Removal:
1. Remove the four screws retaining the panel below the steering column and remove the panel.
2. Extract the four screws from inside the top edge of the instrument cluster trim.
3. Remove the two screws from the lower instrument cluster trim, one on each side of the steering column.
4. Remove the dash trim panel.
LEFT SIDE
RIGHT SIDE
5. Remove the four
"D1" BRACKET USE HOLE #3
LADO
LADO
"C1" BRACKET USE HOLE #2
"D1" SOPORTE
7mm hex screws
"C1" SOPORTE
IZQUIERDA
DERECHO
USA ABERTURA
USA
from the radio
NO. 3
ABERTURA
brackets/dummy
NO. 2
3
2
panel. Pull the radio
out of the cavity,
disconnect the
antenna, speaker
leads and all the
electrical
FRONT OF KIT
2
3
FRENTE DE
"D2" BRACKET
ESTUCHE
USE HOLE #3
connections, then
"C2" BRACKET
USE HOLE #2
remove the radio.
"D2" SOPORTE USA ABERTURA NO. 3
"C2" SOPORTE USA ABERTURA NO. 2
USE THE SHADED BRACKETS & THE INDICATED HOLE LOCATIONS. CUT OFF THE REMAINING BRACKETS AND DISCARD.
Usa los soportes asombrados y las localizaciónes de aberturas indicadas. Corta los soportes que sobran y desechalas.
1982-89 Oldsmobile Toronado
Read pages
3-7 for kit
Radio Removal:
assembly.
1. Remove the five screws from the top underside of the dash trim.
2.
Lower the tilt wheel and gently pull out on the trim piece from the top side. This allows clearance to
disconnect the electrical connections. Remove the connections and the panel.
3. Remove the ten screws securing the
LEFT SIDE
RIGHT SIDE
climate controls
"B1" BRACKET USE HOLE #2
"A1" BRACKET USE HOLE #1
LADO
LADO
"B1" SOPORTE
and the radio, six
"A1" SOPORTE
IZQUIERDA
DERECHO
USA
screws from the
USA
ABERTURA
ABERTURA
climate controls
NO. 1
NO. 2
4
and four screws
2
from the radio.
4. Disconnect the
antenna,
speakers, and all
the electrical
connections and
FRONT OF KIT
remove the radio.
"B2" BRACKET
FRENTE DE
4
"A2" BRACKET
USE HOLE #2
2
ESTUCHE
USE HOLE #1
"B2" SOPORTE USA
"A2" SOPORTE USA
ABERTURA NO. 2
ABERTURA NO. 1
USE THE SHADED BRACKETS & THE INDICATED HOLE LOCATIONS. CUT OFF THE REMAINING BRACKETS AND DISCARD.
Usa los soportes asombrados y las localizaciónes de aberturas indicadas. Corta los soportes que sobran y desechalas.
Read pages
1989-93 Oldsmobile Touring Sedan
3-7 for kit
assembly.
Radio Removal:
1. Open the center console storage compartment, then remove the two screws securing the storage sleeve/
pocket. Remove the sleeve/pocket insert.
2. Remove the two screws from the front edge of the console pocket (at the wood trim), then remove the
trim section.
3. Pop out and remove the electric seat control panel (located in the center console).
4. Carefully snap off the trim piece from around the gear
"C2" BRACKET USE HOLE #2
selector, then remove the four screws securing the wood
"D2" BRACKET
"C2" SOPORTE
trim to the console substructure.
USA ABERTURA NO. 2
USE HOLE #2
"D2" SOPORTE
5. Remove the wood trim piece from the top of the console,
USA ABERTURA
NO. 2
pull the trim piece back and
TOP
up to remove. Disconnect the
TOPE
wire harnesses and remove
"A1" BRACKET
the trim piece.
USE HOLE #2
"A1" SOPORTE
6. Extract the four screws
USA
which secure the radio, pull
ABERTURA
NO. 2
the radio out of the cavity,
disconnect the wire
BOTTOM
FONDO
harnesses and the antenna,
then remove the radio.
"B2" BRACKET USE HOLE #2
"B2" SOPORTE USA ABERTURA NO. 2
USE THE SHADED BRACKETS & THE INDICATED HOLE LOCATIONS. CUT OFF THE REMAINING BRACKETS AND DISCARD.
Usa los soportes asombrados y las localizaciónes de aberturas indicadas. Corta los soportes que sobran y desechalas.
27
