scigiene NV-N20K48, Руководство пользователя, Страница: 41 / 56

41
/57
7.3.2.5
ALARMS
This tab allows you to configure the parameters related to the alarm functions:
QuickTu
ne
QuickTune Mobile
Alarms tab
•
Alarm 1 Function:
Allows you to define alarm 1 function: “Off”, “Minimum”, “Maximum”, “Differential”, “Minimum Differential”,
“Maximum Differential”, “Open Sensor”, “Ramps and Soaks Event”, “End of Soak” or “Open Loop” (see
ALARM CONFIGURATION
section).
•
Alarm 2 Function:
Allows you to define alarm 2 function: “Off”, “Minimum”, “Maximum”, “Differential”, “Minimum Differential”,
“Maximum Differential”, “Open Sensor”, “Ramps and Soaks Event”, “End of Soak” or “Open Loop” (see
ALARM CONFIGURATION
section).
•
Alarm 3 Function:
Allows you to define alarm 3 function: “Off”, “Minimum”, “Maximum”, “Differential”, “Minimum Differential”,
“Maximum Differential”, “Open Sensor”, “Ramps and Soaks Event”, “End of Soak” or “Open Loop” (see
ALARM CONFIGURATION
section).
•
Alarm 4 Function:
Allows you to define alarm 4 function: “Off”, “Minimum”, “Maximum”, “Differential”, “Minimum Differential”,
“Maximum Differential”, “Open Sensor”, “Ramps and Soaks Event”, “End of Soak” or “Open Loop” (see
ALARM CONFIGURATION
section).
PARAMETERS OF EACH ALARM:
Each type of alarm has specific parameters. The sections below present the configuration parameters for Alarm 1 function
modes, but all alarms have the same parameters.
MINIMUM ALARM
•
Alarm 1 SP: Allows you to define the trigger point for Alarm 1. Range: According to the minimum and maximum SP limits configured.
•
Alarm 1 Initial Blocking: Allows you to define whether there will be an initial block of alarm 1 (see ALARM INITIAL BLOCK FUNCTION
section).
•
Alarm 1 Hysteresis: Allows you to define a hysteresis value for Alarm 1.
•
T1 of Alarm 1: Allows you to define a timer interval for the activation of Alarm 1. Range: 0 ~ 5999 (in seconds).
•
T2 of Alarm 1: Allows you to define a second timer interval for the activation of Alarm 1. Range: 0 ~ 5999 (in seconds).
•
Displays SPA1 in the Operation Cycle: Allows you to define whether the SPA1 of Alarm 1 will be displayed in the Operation Cycle of the
device.
•
Flash in Alarm 1: Allows you to define whether Alarm 1 will display an alert flag on the display when it is in an alarm situation (see
DISPLAY INFORMATION section).
MAXIMUM ALARM
•
Alarm 1 SP: Allows you to define the trigger point for Alarm 1. Range: According to the minimum and maximum SP limits configured.
•
Alarm 1 Initial Blocking: Allows you to define whether there will be an initial block of alarm 1 (see ALARM INITIAL BLOCK FUNCTION
section).
•
Alarm 1 Hysteresis: Allows you to define a hysteresis value for Alarm 1.
•
T1 of Alarm 1: Allows you to define a timer interval for the activation of Alarm 1. Range: 0 ~ 5999 (in seconds).
•
T2 of Alarm 1: Allows you to define a second timer interval for the activation of Alarm 1. Range: 0 ~ 5999 (in seconds).
•
Displays SPA1 in the Operation Cycle: Allows you to define whether the SPA1 of Alarm 1 will be displayed in the Operation Cycle of the
device.
•
Flash in Alarm 1: Allows you to define whether Alarm 1 will display an alert flag on the display when it is in an alarm situation (see
DISPLAY INFORMATION section).