116
Appendix
SPB Operation Manual
Minimum Pipe Wall Thickness
Single Wall
PIPE WALL THICKNESS
0
.025"
.050"
.075"
.100"
.125"
.150"
.175"
.200"
.225"
.250"
.275"
.300"
.325"
.350"
.375"
0
200
400
600
800
1000
1200
1400
1600
1800
2000
2200
2400
2600
2800
3000
3200
3400
3600
3800
4000
4200
0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
190
200
210
220
230
240
250
260
270
280
290
300
SCHEDULE 40
(1/4 wall)
9 gauge
3/16”
11 gauge
7 gauge
MA
TERIAL
PRESSURE
BAR
PSI
1. This chart assumes a safety factor of 2:1. Higher safety factors may be required in some circumstances.
2. Wear reduces wall thickness. Thickness must be checked on a regular basis.
3. Pressures may be limited even more by clamp style or pipe end used.
4. The chart is based on 62,000 PSI tensile strength. Heat-treated calculations are based on 120,000 PSI tensile strength.
5. The chart is for pressure calculations ONLY. There is no allowance for mechanical forces other than pressure, and thicker walls
may be needed for mechanical strength because of support or restraint considerations.
6. The chart does not take into account metal fatigue caused by pressure cycles.
7. The chart does not apply to the system at the back end of the pump. The outlet pipe, tapered bend, 6 inch elbow, and 6 to 5
reducer have a minimum wall thickness of 2mm or .079 inches, and must be able to handle the maximum material pressure of
the pumpkit.
Note! This chart is intended as a guide for concrete pumping applications and is subject to the notes,
assumptions, and conditions listed above. Any other use of this chart is not recommended.
This chart does not apply to double-wall pipe. Double wall pipe can be checked by inspecting the inside of the pipe. If the insert is intact, the pipe is
okay. If the insert is worn through, the pipe must be replaced. Contact your pipe supplier for the pressure capacity of your double-wall pipe.
pipewallvsPress2.eps
.heat treated
.standard
4“ HE
AT
TREA
TE
D
5“ HE
AT
TREA
TED
6“ HE
AT
TREA
TE
D
4.8” & 4.9“
HEA
T
TREA
TED
4.4” HE
AT
TREA
TE
D
4.9“ (7, 9,
11
gauge) system (1
25 mm)
6“ sy
stem
5“ syste
m
4.0“ sys
tem
4.4“ system
4.8“ syste
m
0.120”
0.150”
0.177”
0.188”
0.250”
Содержание SPB 28
