manualshive.com logo in svg

Schweitzer Engineering SEL-2032, Инструкция по эксплуатации


Поделиться
Скачать
background image

7.38

SEL-2032

 

Communications Processor

Instruction Manual

Date Code 20120126

Settings

SER (SET R) Settings

SER (SET R) Settings

Use the 

SET R

 command to define which bits are monitored for Sequential 

Events Recorder (SER) data. 

This settings class has no labels or prompts. You enter the names of those 
SEL-2032 elements that you wish to monitor for SER tracking. The only 
elements that are allowed are the Digital Input elements IN1–IN16. You may 
monitor one or all of these elements. Because the Digital Inputs are available 
only with the optional IO Board installed, the 

SET R

 command has no effect 

when the IO Board is not installed.

The various editing keys and commands are listed in 

Table 7.9

. You may enter 

only a single element name on each line. To complete the settings process you 
may either type END followed by 

<Enter>

 or simply hit 

<Enter>

 at a blank 

line.

In order to use the SER data that is generated as a result of these settings, you 
must enable the SEL-2032 to transmit the data via a binary protocol (see 

Logic 

(SET O) Settings

).

ZPICKUP

Z Timer Pickup time (seconds). 

The range is 0.0–86400.0 seconds in 0.1-second increments.

ZDROPOUT

Z Timer Dropout time (seconds).

 

The range is 0.0–86400.0 seconds in 0.1-second increments.

ALARM

ALARM= Enter 

a 

SEL

OGIC

 control equation to control the alarm contact. 

Independent of this equation, the alarm contact asserts (closes) 
for self-test failures. Use this setting to control under what other 
conditions you want the alarm contact to close. The default
setting causes the alarm contact to pulse on access level change 
to Access Level 2, successive password failures, and settings 
changes.

DEBOUNCE

Input debounce time:

(0 = OFF, 1 = 8 ms, 2 = 16 ms, 3 = 24 ms, 4 = 

32 ms)

Use this setting to enable a software debounce on the SEL-2032 
inputs. This setting is only available if the optional I/O board is 
installed.

OUT1

Output contact 1 assignment. 

You enter a SEL

OGIC

 control equation definition for contact 

OUT1. This setting is available only if the optional I/O board is 
installed.

OUT2

Output contact 2 assignment. 

You enter a SEL

OGIC

 control equation definition for contact 

OUT2. This setting is available only if the optional I/O board is 
installed.

OUT3

Output contact 3 assignment. 

You enter a SEL

OGIC

 control equation definition for contact 

OUT3. This setting is available only if the optional I/O board is 
installed.

OUT4

Output contact 4 assignment. 

You enter a SEL

OGIC

 control equation definition for contact 

OUT4. This setting is available only if the optional I/O board is 
installed.

Table 7.11

Global (SET G) Settings and Definitions 

 (Sheet 2 of 2)

Setting

Comment

Description

Courtesy of NationalSwitchgear.com

Содержание SEL-2032



































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SEL-2032

D-Link DXS-3610-54S Quick Installation Manual preview
DXS-3610-54S
Бренд: D-Link Страницы: 38
D-Link Web Smart DES-1210-28P Selection Manual preview
Web Smart DES-1210-28P
Бренд: D-Link Страницы: 6
D-Link xStack Storage DSN-4000 Series Manual preview
xStack Storage DSN-4000 Series
Бренд: D-Link Страницы: 23
D-Link Express EtherNetwork DI-604 Brochure preview
Express EtherNetwork DI-604
Бренд: D-Link Страницы: 7
D-Link xStack Storage DSN-4000 Series Cli User'S Manual preview
xStack Storage DSN-4000 Series
Бренд: D-Link Страницы: 97
XESS XStend XS40 User Manual preview
XStend XS40
Бренд: XESS Страницы: 23
Stanwax Laser ILDA Gem Laser projector tool Instructions preview
ILDA Gem Laser projector tool
Бренд: Stanwax Laser Страницы: 3
IDT TSI384 User Manual preview
TSI384
Бренд: IDT Страницы: 281
DMX4ALL DMX-Universal-Demux User Manual preview
DMX-Universal-Demux
Бренд: DMX4ALL Страницы: 17
Rockwell Automation 41LR4060 Instruction Manual preview
41LR4060
Бренд: Rockwell Automation Страницы: 108
3Com Token Ring Getting Started Manual preview
Token Ring
Бренд: 3Com Страницы: 18
Supermicro SC836 X9 User Manual preview
SC836 X9
Бренд: Supermicro Страницы: 24
Baldor Modbus Plus Installation And Operating Manual preview
Modbus Plus
Бренд: Baldor Страницы: 34
ZALMAN RESERATOR 1 Manual preview
RESERATOR 1
Бренд: ZALMAN Страницы: 22
Supermicro Optane Persistent Memory 200 Series User Manual preview
Optane Persistent Memory 200 Series
Бренд: Supermicro Страницы: 54
GarrettCom Industrial Network Track OSI Brochure preview
Industrial Network Track OSI
Бренд: GarrettCom Страницы: 10
Adaptec 2410SA - Serial ATA RAID Controller Hardware Installation Manual preview
2410SA - Serial ATA RAID Controller
Бренд: Adaptec Страницы: 14
CAME 848EA-0120 Setup And User'S Manual preview
848EA-0120
Бренд: CAME Страницы: 32

Бренды по названию

Популярные бренды

Загрузить еще бренды