background image

 

Basic safety notes 

  

 

 

01.00|SWS-001 |en 

 

 

Product safety 

Dangers arise from the product, if: 
  •  the product is not used in accordance with its intended pur-

pose. 

  •  the product is not installed or maintained properly. 
  •  the safety and installation notes are not observed. 
Avoid any manner of working that may interfere with the function 
and operational safety of the product. 
Wear protective equipment. 

  

 

NOTE 

More information are contained in the relevant chapters. 

 

Protective equipment 

Provide protective equipment per EC Machinery Directive. 

 

Constructional changes, attachments, or modifications 

Additional drill holes, threads, or attachments that are not offered 
as accessories by SCHUNK may be attached only with permission 
of SCHUNK. 

 

Personnel qualification 

The assembly, initial commissioning, maintenance, and repair of 
the product may be performed only by trained specialist person-
nel. Every person called upon by the operator to work on the 
product must have read and understood the complete assembly 
and operating manual, especially the chapter "Basic safety notes" 

(

 2, Page 6)

. This applies particularly to personnel only used oc-

casionally, such as maintenance personnel. 

 

Using personal protective equipment 

When using this product, you must comply with the relevant 
health and safety at work rules and you must use the required 
personal safety equipment (minimum: category 2). 

2.4 

2.4.1 

2.4.2 

2.5 

2.6 

Содержание SWS-001









































Отзывы: