SCHUNK DPG-plus 100 Скачать руководство пользователя страница 59

Страница: 59 / 80

Maintenance

28.00 | DPG-plus | Assembly and Operating Manual | en | 389031

7.6.4 Version with "force amplification cylinder" (KVZ)

Position of the item numbers:
•

Previous version:

Assembly drawing (previous version)

[

}

65]

•

Successor version:

Assembly drawing (successor version)

[

}

68]

Dismantling

Remove the compressed air hose.

Unfasten and remove the screws (47).

Previous version:

Remove the cover (5) and seal (37/20).

Successor version:

Remove the cover (5) and flat seal (20).

Mark the installation positions of the piston (3/8), the base jaws
(2/7) and the side cover (12) on the housing (1).

Previous version:

Unscrew screws (42). Remove the side

cover (12) and the gasket (14).
For DPG-plus 240 / 300: Remove O-ring (39).

Successor version:

Unscrew and remove screws (42), remove

the side cover (12) and the flat seal ring (39).

IMPORTANT! Do not disassemble the filler piece (18) for
maintenance purposes, as the product may leak. If the filler
piece (18) is nevertheless disassembled, seal the filler piece
(18) with liquid sealant on reassembly.

Unscrew and remove the screws (41) and remove the cover (4).

Unscrew the screw (40/45) and remove the cylinder
piston (10/6) from the intermediate housing (65).

Remove the intermediate housing (65).

Previous version:

Mark the installation position between the

cylinder piston (60) and the housing (1).

Successor version:

Mark the installation position between the

cylinder piston (71) and the housing (1).

Remove the intermediate piston (66).

Previous version:

Remove the second cylinder piston (60) from

the housing (1).

Successor version:

Remove the second cylinder piston (71) from

the housing (1).

Push the pistons (3/8) upwards out of the housing (1).

NOTE

Do not disassemble the intermediate jaw (13) from the base jaw
(2/7).

Pull the base jaws (2/7) out of the housing (1).

Loosen the screw (43) and disassemble the intermediate
jaw (13) from the base jaw (2/7).

Содержание DPG-plus 100

















































































Результаты поиска

Содержание DPG-plus 100

Отзывы:

Похожие инструкции для DPG-plus 100

Бренды по названию

Популярные бренды

SCHUNK DPG-plus 100, Сборка и руководство по эксплуатации

Результаты поиска

Содержание DPG-plus 100

Отзывы:

Похожие инструкции для DPG-plus 100

Бренды по названию

Популярные бренды