manualshive.com logo in svg

SCHUNK 1487754, Сборка и руководство по эксплуатации

Поделиться
Скачать
SCHUNK 1487754 Скачать руководство пользователя страница 27

Operation

8.2 Processing

 DANGER

Flying workpiece due to insufficient clamping force during
machining, resulting from insufficient vacuum or excessive
machining forces.

Risk of injury or death due to flying workpiece

•

Monitor the vacuum value as close to the clamping location as
possible.

•

Wear personal protective clothing.

Processing steps in chronological order:
1. Place the workpiece on the Matrix-Plate.
2. Activate the vacuum using the manual slide valve. Support

suctioning of the workpiece, if necessary, by pressing it onto the
Matrix-Plate.

3. Check that the workpiece is securely held.
4. Start processing according to the machine specifications.
5. Once processing is complete, deactivate the vacuum using the

manual slide valve. The Matrix-Plate is vented automatically and
the workpiece can be removed.

To process workpieces on the complete machine, an operating
vacuum of at least -750 mbar is recommended. This is monitored
by the gauge. This does not mean that processing cannot also be
carried out at a lower vacuum level. To measure the vacuum, the
gauge must be connected directly to the Matrix-Plate.

Note:

A vacuum drop may cause the workpiece that is being machined
on the machine table to move or even be released. 
Possible causes for a vacuum drop include:
• Power failure
• Sudden leakage
• Line break
• Malfunction
• Perforation in the workpiece due to machining
• Contaminated filter on the vacuum vent

27

01 | Matrix-Plate SMPL | Assembly- and Operating Manual | en-US | 0489081

Содержание 1487754









































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды