SCHUNK 1487754 Скачать руководство пользователя страница 12

Страница: 12 / 40

Product Description

01 | Matrix-Plate SMPL | Assembly- and Operating Manual | en-US | 0489081

Gauge connection kit

Additional thread for side stops

Matrix-Plate with groove grid

Side stops

Vacuum vents with filter and G1/8
plugs

Connection kit for hose connection

Vacuum vents with G1/4 plugs

M12 thread for connecting zero point
clamping system

Slot for holding clamping claws

Mounting holes for connection kit for
hose connection

3.2 Variants and Type Key

The Matrix-Plate SMPL is available in six different versions. The
version is indicated in the item designation. The item designation
is composed as follows:

Part
number

Short
description

Dimensions
[mm]

Grid
spacing
[mm]

Slot
width x depth
[mm]

Frictio
n
pad

Number of
vacuum
openings

1487757 SMPL

600x400x28

25x25

3x3

1487758 SMPL

600x400x28

25/12.5

3x3

---

1487755 SMPL

400x300x28

25x25

3x3

1487756 SMPL

400x300x28

12.5x12.5

3x3

---

1487754 SMPL

300x200x28

12.5x12.5

3x3

---

All specifications are in mm (except for the number of vacuum
vents).

= On Matrix-Plate 1487758, a quarter of the area is designed in a

12.5x12.5 grid and the remaining area in a 25x25 grid.

Содержание 1487754









































Результаты поиска

Содержание 1487754

Отзывы:

Бренды по названию

Популярные бренды

SCHUNK 1487754, Сборка и руководство по эксплуатации

Результаты поиска

Содержание 1487754

Отзывы:

Бренды по названию

Популярные бренды