Schulte Titan 5000 II Series Скачать руководство пользователя страница 96

Страница: 96 / 108

OPERATION

Titan 5000 Series II 01/22

Operation Section 4-34

OPERA

ION

13. TROUBLESHOOTING GUIDE

Problem

Possible Cause

Remedy

Reel does not turn

Oil not getting into hydraulic

Check hydraulic connections

motor.

Check tractor flow control valve

Throwing rocks over back

Reel speed too fast

Adjust flow control on tractor

Reel not sweeping rocks

Batts springs too loose

Tighten springs

into bucket. Excessive
batt tripping

Excessive jerky Reel

compressed coupler insert

Replace coupler insert

motion

Reel coupler not tight on shaft

Tighten reel coupler and lock

Rock thrown over sides

Overfilling bucket

Dump bucket more frequently

and forward

Bucket not filling

Insufficient reel speed

Adjust flow control to tractor

Picking up too much dirt

Poor field conditions

Soil should be firm and dry

Minimum of surface debris

Teeth penetrating too much

Raise grate so teeth just skim

surface

Reel slows significantly when

Open center hydraulic system

Machine must be run on a tractor

the grate is moved

on the tractor.

with a Closed Center Hydraulic System

Содержание Titan 5000 II Series













































































































Результаты поиска

Содержание Titan 5000 II Series

Отзывы:

Schulte Titan 5000 II Series, Руководство оператора, Страница: 96 / 108

Результаты поиска

Содержание Titan 5000 II Series

Отзывы: