Schulte Titan 5000 II Series Скачать руководство пользователя страница 18 | Manualshive

Страница: 18 / 108

Schulte Titan 5000 II Series Скачать руководство пользователя страница 18

SAFETY

Titan 5000 Series II 01/22

Safety Section 1-12

© 2022 Alamo Group Inc.

SAFETY

Cancer and Reproductive Harm

www.P65Warnings.ca.gov.

Concluding Safety Instructions and Practices

All Safety Shields, Guards and other safety devices including (but not limited to) Deflectors,
Steel Guards and Gearbox Shields must be used and maintained in good working
condition. All safety devices should be inspected carefully at least daily for missing or
broken components. Missing, broken, or worn items must be replaced at once to reduce the
possibility of injury or death from thrown objects, entanglement, or contact.

(SSM-07)

I

n addition to the design and configuration of this Implement, including Safety Signs and Safety Equipment,

hazard control and accident prevention are dependent upon the awareness, concern, prudence, and proper
training of personnel involved in the operation, transport, maintenance, and storage of the machine. Refer
also to Safety Messages and operation instruction in each of the appropriate sections of the Tractor and
Equipment Manuals. Pay close attention to the Safety Signs affixed to the Tractor and Equipment.

(SG-18)

PARTS INFORMATION

Schulte Products use balanced and matched system components for blade carriers, blades, cuttershafts,
knives, knife hangers, rollers, drivetrain components, and bearings. These parts are made and tested to
Schulte Industry specifications. Non-genuine "will fit" parts do not consistently meet these specifications. The
use of “will fit” parts may reduce the performance, void Schulte warranties, and present a safety hazard. Use
genuine Schulte parts for economy and safety.

(SPSI-1)

SEE YOUR SCHULTE DEALER

«
...
16
17
18
19
20
...
»

Содержание Titan 5000 II Series













































































































Отзывы:

Нет отзывов