manualshive.com logo in svg

Schmidt SS 20.700, Инструкция по эксплуатации

Поделиться
Скачать
Schmidt SS 20.700 Скачать руководство пользователя страница 28

Instructions for Use 

– SCHMIDT

®

 Flow Sensor SS 20.700 

Page 28

 

6  Commissioning 

Prior to switching on the 

SCHMIDT

®

 Flow Sensor SS 20.700

, the follow-

ing checks have to be carried out: 

  Mechanical installation: 

o

  Correct immersion depth and alignment of the sensor probe accord-

ing to flow direction 

o

  Tightening of fastening screw or spigot nut 

o

  Installation of pressure safety measures 

 

For measurements in media with overpressure, check if the 
fastening screw is tightened properly and pressure safety 
devices are installed. 

  Connecting cable: 

o

  Correct connection in the field (switch cabinet or similar) 

o

  Tightness of sensor connector and connecting cable (flat seal must 

be inserted correctly into the female cable connector) 

o

  Tight fit of spigot nut of cable connector at the sensor enclosure 

After switching on the supply voltage, the sensor signals its initialization 
by switching all four LEDs in the enclosure cover sequentially to red, or-
ange and green. 
If the sensor detects a problem during initialization, it signals the problem 
with the cover LEDs according to Table 5. An extensive overview of pos-
sible errors, their causes as well as troubleshooting measures are listed 
in Table 10. In addition the ring LEDs shows 

  Complete lights green: sensor is fully operational 

  Comlete ring flashes red: sensor is defective 

If the sensor is operating as intended after the initialisation, it switches into 
regular  measuring  mode.  For  a  short  period  the  flow  velocity  indication 
(both LED strip and signal outputs) goes to maximum and settles to the 
correct  measuring  value  after  about  10  seconds,  provided  the  sensor 
probe  was  already  at  medium  temperature.  Otherwise,  the  process  will 
last longer until the sensor has reached the medium temperature. 

7  Information concerning operation 

Environmental condition Temperature 

The 

SCHMIDT

®

 Flow Sensor SS 20.700

 monitors both the medium and 

the  electronics  temperature.  As  soon  as  one  of  the  specified  operating 
ranges is left, the sensor switches off both measuring functions associated 
with the medium and signals this error via the LED strip (according to Ta-
ble 5) as via the light ring. 

Содержание SS 20.700





































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды