Schmidt DT Series Скачать руководство пользователя страница 11

Страница: 11 / 16

3.4.2.1 Delay Mode

rpm

: Light will flash in correspondence with

input signal; the input signal will be

calculated into rpm and displayed.

deg

: One cycle of input signal is 360°.

A delayed angle will be displayed from 0

up to 359°. (The delayed angle can be

changed by turning the setter as

previously described).

msec

: The above delayed angle will

be displayed in msec.

If the input signal frequency exceeds upper or lower limits, the alarm dashes

(

)

will be displayed and the strobe will stop flashing (see chapters

3.4.2.3 and 3.4.2.4).

If the Auto Power Off timer is used:

Once the internal timer has expired, the strobe will stop flashing and the display

will flash rapidly. To restart the strobe, turn power switch off, then on, and the

cycle will repeat. (see chapter 3.5)

3.4.2.2 RPM Display Mode

If the input signal exceeds 585 Hz, the upper dashes on the digital display

will be flashing:

upper dashes

If the input signal is lower than 0.65 Hz, the lower dashes on the digital

display

will be flashing:

lower dashes

3.4.2.3 Deg/msec Display Mode

If the input signal exceeds 167 Hz, the upper dashes on the digital display

will be flashing:

If the input signal is lower than 0.67 Hz, the lower dashes on the digital

display

will be flashing:

upper dashes

msec

deg

lower dashes

msec

Содержание DT Series

















Результаты поиска

Содержание DT Series

Отзывы:

Похожие инструкции для DT Series

Бренды по названию

Популярные бренды

Schmidt DT Series, Руководство по эксплуатации

Результаты поиска

Содержание DT Series

Отзывы:

Похожие инструкции для DT Series

Бренды по названию

Популярные бренды