schmersal SLC440 Скачать руководство пользователя страница 15

Страница: 15 / 20

SLC440 Series

SLG440 Series

Operating instructions

Safety light curtain / safety light grid

4.7 Accessories, included in delivery

Mounting kit MS-1100

The mounting kit consists of 4 pcs steel angles and 8 pcs fixing

screws

5,5

MSD5 spacer

The kit comprises 2 pcs of spacers and is included in delivery as of a

protection field height of 1050 mm The spacers must be used in case

of vibrations

7,7

4.8 Optional accessory

Centre support MS-1110

Mounting kit consists of 2 pcs steel angles and 4 pcs spacers for

central fixing

27,8

11,5

19,5

11,5

54,3

5,5

Connecting cable for emitter
Article No. Designation (description)

Length

101207741 KA-0804 (female connector M12, 4-pole)

5 m

101207742 KA-0805 (female connector M12, 4-pole)

10 m

101207743 KA-0808 (female connector M12, 4-pole)

20 m

Connecting cable for receiver
Article No. Designation (description)

Length

101207728 KA-0904 (female connector M12, 8-pole)

5 m

101207729 KA-0905 (female connector M12, 8-pole)

10 m

101207730 KA-0908 (female connector M12, 8-pole)

20 m

Adapter cable for parameter setting
Article No. Designation (description)

Length

101217615 KA-0974 (Y-distributor with command device)

1 m

Status indicator

The status indication at the receiver indicates the switching condition

of the outputs OSSD1 and OSSD2 and the function restart interlock /

setup

Green = outputs H-signal 24V

Red = outputs L-signal 0V

Yellow = restart interlock

Blue = setup mode/Bluetooth

Test rod PLS

The test rod is used for testing the protection field

MSD4 Vibration damper

Kit consists of: 8 pcs vibration dampers 15 x 20 mm, 8 pcs M5 cylinder

head screws with hexagon socket, 8 pcs spring washers Mounting

using MS-1100

The MSD4 vibration damper kit is recommend to be used for damping

vibrations and oscillations on the AOPD For applications with higher

mechanical stresses, eg presses, punching machines, we recommend

the MSD4 kit In this way, the availability of the AOPD is increased

Содержание SLC440





















Результаты поиска

Содержание SLC440

Отзывы:

Похожие инструкции для SLC440

Бренды по названию

Популярные бренды

schmersal SLC440, Руководство по эксплуатации

Результаты поиска

Содержание SLC440

Отзывы:

Похожие инструкции для SLC440

Бренды по названию

Популярные бренды