schmersal SEP 01.0 Скачать руководство пользователя страница 5

Страница: 5 / 38

SEPK 02.0 / SEPG 05.3 / SEP 01.0 /

SEP 01.4 / SEPLC 05.2 / SEP 07.0 / SEP 09.0

Operating instructions

Two-hand control panel

2.4 Ordering code emergency stop command device EDR...

EDR

➀ ➁ ➂ ➃

EFR

No. Option

Description

➀

latching only in combination with EFR,

turn and pull to unlock

latching only in combination with EFR,

turn to unlock

with cylinder lock, unlocking only by key,

only by pulling, with EFR

➁

Head diameter 49 mm

Head diameter 38.5 mm

➂

Mounting hole 22,3 mm

Mounting hole 30,5 mm

➃

Red colour

Not all component variants, which are possible according to this order

code, are available.

2.5 Ordering code emergency stop command device KDRR...

KDRR

➀ ➁ ➂ ➃

EFR

No. Option

Description

➀

Plastic device head, release by turning and

pulling

Release by pulling only

➁

Head diameter 38.5 mm

Head diameter 49 mm

➂

Mounting hole 22,3 mm

Mounting hole 30,5 mm

➃

Red colour

Not all component variants, which are possible according to this order

code, are available.

2.6 Ordering code emergency stop command device ADRR 40

ADR

➀ ➁ ➂

No. Option

Description

➀

Release by pulling

➁

Head diameter 40 mm

➂

Red colour

Not all component variants, which are possible according to this order

code, are available.

2.7 Ordering code emergency stop command device EDRZ...

EDRZ

➀ ➁ ➂

No. Option

Description

Release by pulling only

➀

Head diameter 38.5 mm

➁

Mounting hole 22,3 mm

Mounting hole 30,5 mm

➂

Red colour

Not all component variants, which are possible according to this order

code, are available.

2.8 Ordering code emergency stop command device (Siemens)

3SB3000-1HA20

No. Option

Description

Command device, red colour, mounting

diameter 22.3 mm, head diameter 40 mm, in

combination with 3SB 3SB3400OC

switching elements (1 NO + 1 NC) or

3SB3400-OD + 3SB3400-OE (2 NO + 2 NC,

in separated form)

2.9 Ordering code operating push buttons (Siemens)

3SB3000-1GA11

No. Option

Description

black, mounting diameter 22.3 mm, head

diameter 40 mm, in combination with

3SB 3SB3400OC switching

elements (1 NO + 1 NC) or 3SB3400-OD +

3SB3400-OE (2 NO + 2 NC, in separated

form)

2.10 Ordering code contact elements for operating push buttons

(Siemens)

3SB3400-O

➀

No. Option

Description

➀

NO element: in combination with

3SB3400-OC switching element = 1 NO + 1

NC element: in combination with 3SB3400-

OB switching element = 1 NO + 1 NC

NO element in combination with 3SB3400-

OE switching element = 2 NO + 2 NC, in

separated form

NC element: in combination with 3SB3400-

OD switching element = 2 NC + 2 NO, in

separated form

➀

NO element in combination with AF10 swit-

ching element = 1 NO + 1 NC, in separated

form

NC element in combination with AF02 swit-

ching element = 1 NO + 1 NC, in separated

form

2.11 Ordering code safety monitoring module SRB 201 ZH

This operating instructions manual applies to the following types:

SRB 201ZH

Only if the information described in this operating instructions

manual are realised correctly, the safety function and therefore

the compliance with the Machinery Directive is maintained.

2.12 Special versions

For special versions, which are not listed in the order code below 2.1,

these speciications apply accordingly, provided that they correspond to

the standard version.

2.13 Destination and use

The two-hand control panels of the series SEPK 02.0 / SEPG 05.3 /

SEP 01.0 / SEP 01.4 / SEPLC 05.2 / SEP 07.0 / SEP 09.0 are used

on machinery and plants as safe command device (as man-machine

interface).

Содержание SEP 01.0







































Результаты поиска

Содержание SEP 01.0

Отзывы:

Похожие инструкции для SEP 01.0

Бренды по названию

Популярные бренды

schmersal SEP 01.0, Руководство по эксплуатации

Результаты поиска

Содержание SEP 01.0

Отзывы:

Похожие инструкции для SEP 01.0

Бренды по названию

Популярные бренды