schmersal SEP 01.0 Скачать руководство пользователя страница 17

Страница: 17 / 38

SEPK 02.0 / SEPG 05.3 / SEP 01.0 /

SEP 01.4 / SEPLC 05.2 / SEP 07.0 / SEP 09.0

Operating instructions

Two-hand control panel

The STPLC...type stand from Elan is equipped with a protective ground

wire connection on the upper lange plate, which the user must connect

with the protective ground wire system when the cable is fed through

the stand tube.

6.3 Additions/notes for die-cast aluminium (AL-226) two-hand

control panels of the type SEPG05.3...

Stand assembly/grounding

• If the SEPG05.3... is itted onto an Elan stand of the STP..., STPSK...,

FES..., FBES... type or other versions of stands (e.g. selfmade solu-

tions), the outer two ground bolts on the ZPL intermediate plate must

be removed by the user.

• If the panel and the stand are ordered or supplied in itted condition

(without additional charges), this step does not apply.

• At the positions provided to that effect, the user must establish a

protective ground wire connection between the upper part of the

SEPG05.3 enclosure and the corresponding bottom part of the enclo-

sure.

• Any further information can be found in the Elan list ZHS/08.

6.4 Special wiring instructions for the STP02... stand

When realising the wiring through the square tube of STP02... type

stands, please observe that only non-hazardous voltages may be

realised. If necessary, an additional ground connection of the stand

base must be provided by the user, whereby "tripping hazards", created

due to the presence of the additionally installed ground wire, must be

prevented.

6.5 Electrical connection of the SRB 201ZH safety-monitoring

module

The electrical connection may only be carried out by autho-

rised personnel in a de-energised condition.

Wiring examples: see appendix

7 Operating principle and settings

7.1 Operating principle and settings SRB 201ZH safety-monitoring

module

LED functions

• K1: Status channel 1

• K2: Status channel 2

Description of the terminals

Voltages:

A1.1

A2.1

+24 VDC/24 VAC

+ 24 V

0 VDC/24 VAC

0 V

Inputs:

S11

S12

S21

S22

Input channel 1 (+)

Input channel 1 (-)

Input channel 2 (-)

Input channel 2 (+)

Outputs:

13-14

23-24

First safety enabling circuit

Second safety enabling circuit

Start:

X1-X2

31-32

Feedback circuit

Auxiliary NC contact

SRB
201ZH

A1 23 13

X1 S12 S11

X2 S22 S21

A2 24 14

A1.1

A2.1

Fig. 14

Notes

The NC contact of the buttons A + B must be opened, before

the NO contact closes. No overlapping contacts to avoid

triggering of the fuses F1 and F2.

The pushbuttons A + B must be actuated within a timeframe

of < 0.5 sec (simultaneous operation monitoring), otherwise

no start enabling signal is given!

Содержание SEP 01.0







































Результаты поиска

Содержание SEP 01.0

Отзывы:

schmersal SEP 01.0, Руководство по эксплуатации, Страница: 17 / 38

Результаты поиска

Содержание SEP 01.0

Отзывы: