Schmalz SMPi 20 Скачать руководство пользователя страница 18 | Manualshive

Страница: 18 / 50

Schmalz SMPi 20 Скачать руководство пользователя страница 18

S

CHMALZ

SCP

I

/

SMP

I

4-18

4 O

PERATING AND MENU CONCEPTS

The  unit  is  operated  via  four  buttons  on  the  membrane  keypad.  Settings  are  made  using
software menus. The operating structure is divided into settings in the basic menu and con-
figuration menu.  Setting  of the  ejector  in  the basic  menu  is  sufficient  for  standard applica-
tions.  An  extended  configuration  menu  is  available  for  applications  with  special  require-
ments.

The ejector is set to display mode when outside the menus. The current vacuum is dis-
played.



The unit of the current vacuum can be displayed by pressing the

button.

Menu authorisation

Menus can be protected against unauthorised access by defining a PIN code

[Pin]

in the

configuration menu.

[Loc]

flashes in the display when the lock is active, or the PIN code is

requested.

The menus are accessed as follows:



Press the

button.



Enter the first digit of the PIN code using the

or

buttons.



Confirm by pressing the

button.



Enter the remaining digits in the same way.



Press the

button to activate the menus.

The lock is activated again automatically after the selected menu or function is exited. The
PIN code “000” must be set for permanent deactivation of the lock.



The PIN code is set to “000” on delivery, meaning the menus are not locked.



If an incorrect PIN code is entered, then

[Loc]

is displayed and the menus

remain locked.

If the correct PIN code has been lost, then the ejector must be sent back to the
manufacturer for authorisation.

«
...
16
17
18
19
20
...
»

Содержание SMPi 20



















































Отзывы:

Нет отзывов