Schmalz SK-JU-110-2000-SRS63-3000-VSL-EX Скачать руководство пользователя страница 8 | Manualshive

Страница: 8 / 63

Schmalz SK-JU-110-2000-SRS63-3000-VSL-EX Скачать руководство пользователя страница 8

SAFETY INSTRUCTIONS

8 | EN

www.schmalz.com

30.30.01.00226/03

1.4 Regulations in these instructions

WARNING

Failure to observe the instructions

Risk of fatal injuries

►

Do not start or use the jib crane until you have read and understood the
operating and maintenance instructions.

These operating and maintenance instructions are an integral part of the jib crane. They must
accompany it wherever it is transported.
These operating and maintenance instructions are specific to the items included in delivery from J.
Schmalz GmbH. They do not take into account any modifications to the jib crane made by the
customer, which are strictly prohibited.
These operating and maintenance instructions do not include the hoist attached to the jib crane (e.g.
vacuum tube lifter).

1.5 General safety instructions

Explosion protection

1.5.1

DANGER

Ignition sources

Risk of explosion

►

When used in potentially explosive atmospheres:



Preclude possible ignition sources (e.g. hot surfaces, open flames, hot
gases or liquids, mechanically produced sparks, adiabatic compression,
shock waves, exothermic chemical reactions, thermal reactions, the
spontaneous combustion of dust, electric arcs or the discharge of static
electricity or propagating brush discharges).



Never allow the components of the jib crane to be hit with force (spark
discharge).



Never strike the components of the jib crane with objects or tools (spark
discharge).

«
...
6
7
8
9
10
...
»

Содержание SK-JU-110-2000-SRS63-3000-VSL-EX
































































Отзывы:

Нет отзывов