Schmalz SK-JU-110-2000-SRS63-3000-VSL-EX Скачать руководство пользователя страница 16 | Manualshive

Страница: 16 / 63

Schmalz SK-JU-110-2000-SRS63-3000-VSL-EX Скачать руководство пользователя страница 16

SAFETY INSTRUCTIONS

16 | EN

www.schmalz.com

30.30.01.00226/03

1.10 Danger zone definition



The danger zone is the area inside or in the vicinity of working equipment that poses a hazard or
potential hazard to the health of persons located within this area.



When lifting the load or transporting it, it is possible that the load could fall, which is why the
swivel range of the jib crane and hoist is always considered a danger zone.

WARNING

Risk of injury from falling objects in case of:

- A collision, causing the load to break off

- Components failing due to incorrect loads and overloads or unauthorized

modifications

There is a risk of death or serious injury from hitting people in the
vicinity.

►

No person may sit or stand in the danger zone of the load.

►

Only work when you have a good view of the entire working area.

►

Pay attention to other people in the working area.

►

Never transport the load above people.

►

The swiveling point of the load must always be located within the working area
of the jib crane.

►

Never release the control handle of the hoist while lifting a load.

►

The working area must be secured by the operator. The persons/equipment
necessary to secure this area must be present during the lifting/transportation
process.

«
...
14
15
16
17
18
...
»

Содержание SK-JU-110-2000-SRS63-3000-VSL-EX
































































Отзывы:

Нет отзывов