manualshive.com logo in svg

Schmalz FMHD Series, Руководство по эксплуатации

Поделиться
Скачать
Schmalz FMHD Series Скачать руководство пользователя страница 8

 

8 |   EN 

www.schmalz.com 

30.30.01.01648/03 

 

 

 

WARNING 

 

 

 

Failure to comply with the general safety instructions

 

 

Personal injuries and damage to the system 

►  Compressed air or a vacuum could cause closed containers to explode or 

implode. Check the products before use. 

 

 

 

 

►  Do not apply suction to any dangerous dusts, oil mists, vapors, aerosols, etc. 

 

 

►  Only use suitable and approved vacuum filters. 

 

 

►  Do not look into the exhaust air flow of the vacuum generator. 

  Intended Use 

1.6

The  system  is  used  to  lift  and  transport  workpieces  such  as  lumber,  wooden  components,  furniture 
parts or similar materials that allow suction. Neutral gases in accordance with EN 983 are approved as 
evacuation  media. Neutral  gases  include  air,  nitrogen  and  inert  gases.  The  device  is  not  suitable  for 
manual handling. Operations using the device must take place in a secure area where no people are 
allowed to enter.  
 

 

 

WARNING 

 

 

 

Suspended loads

 

 

Personal injuries and damage to the system 

►  Never stand under suspended loads. 

 
 
The system is mounted on the load suspension provided by the customer using the T-slots designated 
for this purpose. The customer also provides a control device. 
 
The system can only be used when hung vertically. You must consult the manufacturer regarding tilted 
positions, as well as pivoting or tipping motions. 

  Note on the Type Plate 

1.7

The type plate contains important information about the device. The type plate is firmly attached to the 
exterior of the device. 
 
The type plate contains the following information: 
 

- 

Product Key 

- 

Year of manufacture 

- 

Serial number 

- 

Spare sealing plate product key 

- 

Order number 

- 

Part number 

- 

Manufacturer’s address  

 

The product key and year of construction are important for identifying the device. They must always be 
specified  when  ordering  replacement  parts,  making  warranty  claims  or  making  other  inquiries  about 
the device. 
 

Содержание FMHD Series





















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды