Scheppach 5901318901, Перевод оригинального руководства пользователя, Страница: 35 / 240

www.scheppach.com
GB | 35
18. Only use saw blades recommended by the man -
ufacturer which conform to EN 847-1. Warning!
When changing the saw blade, ensure that the
cutting width is not smaller and the width of the
saw blade disc is not greater than the thickness of
the riving knife!
19. When sawing wood and plastics, avoid the saw
teeth overheating. Reduce the feed speed in order
to avoid the plastic melting.
20. Please note that complex non-through cutting op-
erations and tapered cuts are not permitted.
21. Avoid bevel ripping on bevelling side of the saw
blade.
22. Make sure when mounting or when installing the
parallel stop that it should be aligned parallel to
the saw blade.
6. Technical data
AC motor 220 - 240 V~
Power consumption S6 20% 2200W
Idle speed 5000 min
-1
Carbide saw blade 254 x 30 x 2,8 mm
Thickness of blade disc 1,8 mm
Number of teeth (pre-
assembled saw blade)
24
Riving knife thickness 2,5 mm
Min. size of workpiece
W x L x H
10 x 50 x 1 mm
Tabel size 575 x 555 mm
Left/right table width
extension
575 x 225 mm
Table extansion at the rear 555 x 225 mm
Cutting height max. 45 ° 65 mm
Cutting height max. 0 ° 85 mm
Tilting saw blade 0 - 45°
Extraction connection Ø 35 mm
Weight approx. 28 kg
Technical changes reserved!
*S1: Continuous operation with constant load
**S6 20 %:
Continuous duty with intermittent loading (operating
time 10 min.)
To avoid impermissible overheating of the motor, the
motor should be driven for only 20% of the operating
time with the stipulated nominal power and must then
continue to run with no load for the remaining 80% of
the operating time.
i) Never stand on the table saw, do not use it as
a stepping stool. Serious injury could occur if the
tool is tipped or if the cutting tool is accidentally
contacted.
j) Make sure that the saw blade is installed to ro-
tate in the proper direction. Do not use grind-
ing wheels, wire brushes, or abrasive wheels
on a table saw.
Improper saw blade installation or use of accesso -
ries not recommended may cause serious injury.
Safety instructions for the handling of saw
blades
1. Only use insertion tools if you have mastered their
use.
2. Observe the maximum speed. The maximum
speed specified on the insertion tool may not be
exceeded. If specified, observe the speed range.
3. Observe the motor / saw blade direction of rota-
tion.
4. Do not use any insertion tools with cracks. Sort out
cracked insertion tools. Repairs are not permitted.
5. Clean dirt, grease, oil and water off of the clamping
surfaces.
6. Do not use any loose reducing rings or bushes to
reduce holes on circular saw blades.
7. Make sure that fixed reducer rings for securing the
insertion tool have the same diameter and have at
least 1/3 of the cutting diameter.
8. Make sure that fixed reducer rings are parallel to
each other.
9. Handle insertion tools with caution. They are ide -
ally stored in the originally package or special con -
tainers. Wear protective gloves in order to improve
grip and to further reduce the risk of injury.
10. Prior to the use of insertion tools, make sure that
all protective devices are properly fastened.
11. Prior to use, make sure that the insertion tool
meets the technical requirements of this electric
tool and is properly fastened.
12. Only use the supplied saw blade for cutting wood,
never for the processing of metals.
13. Use the correct saw blade for the material to be
processed.
14. Use only a saw blade with a diameter that match -
es the specifications on the saw.
15. Use only saw blades that are marked with an
equal or higher rotational speed than that marked
on the power tool.
16. Use only saw blades recommended by the manu -
facturer which conform to EN 847-1, if intended for
cutting wood or similar materials.
17. Wear suitable personal protective equipment,
such as:
- Hearing protection;
- Protective gloves when handling saw blades.