Schenker ZEN 30 Скачать руководство пользователя страница 36

Страница: 36 / 44

– MAINTENANCE (ROUTINE AND SPECIAL)

COD.

30Z12/24.B.2021

THE PRESENT MANUAL BELONGS TO -

Schenker Italia

6. MAINTENANCE (ROUTINE AND SPECIAL)

6.1 Check filter cleaning

It is very important to inspect filters condition periodically.
In the system there are the following:

1. Mesh filter (strainer).
2. Pump filter (5 micron cartridge filter

– blue and white filter housing).

3. Active carbon filter.

In order to keep the filters properly clean, follow the tab illustrated hereby:

OPERATION

FREQUENCY

PROCEDURE

Check

and

clean

the

strainer

Every 5 days

Visual inspection and washing

Replace the 5 micron
cartridge filters

It depends on the working
conditions and the turbidity of the
sea water. In average conditions
the replacement of the cartridge is
recommended

every

80-100

working hours. Once replaced the
filters, it is necessary to purge the
air from the system,

opening for 2-

3 minutes the depressurization
valve.

Unscrew the filter housing counter

clockwise by using the specific key

provided

Replace the active carbon
fibre filter

Once per year

Unscrew the filter housing counter

clockwise by using the specific key

provided

Содержание ZEN 30












































Результаты поиска

Содержание ZEN 30

Отзывы:

Бренды по названию

Популярные бренды

Schenker ZEN 30, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание ZEN 30

Отзывы:

Бренды по названию

Популярные бренды