manualshive.com logo in svg

Schenker ZEN 30, Инструкция по установке, эксплуатации и обслуживанию

Поделиться
Скачать
Schenker ZEN 30 Скачать руководство пользователя страница 32

 

 

 

5 

– FUNCTIONING AND USE 

COD.

30Z12/24.B.2021

 

EN 

 

THE PRESENT MANUAL BELONGS TO - 

Schenker Italia 

-  ALL RIGHTS RESERVED 

31 

5.After a while, push FLUSHING in order to flush 
the unit before stopping it.  

       Then the unit will stop after about 1 minute.  

 

 
After  completing  the  procedure,  the  system  will  be 
ready to start normally.  

 

 

5.3  Normal operating procedure 

Preliminary checks:  

1.  Check if the reset valve is closed (lever 

orthogonal

 to the body valve) and the positioner completely 

unscrewed. 

2.  Check if the depressurization valve is closed and that the grey valve on the active carbon filter is open.  

 

5.3.1 

Normal operating procedure without final flushing 

1.  Push ON/OFF to start the watermaker. 

 

 

2.  Push ON/OFF to stop the watermaker. 

 

 

 

   

CAUTION:  
The watermaker 

produces periodic “beats” during its functioning, due to the movement of the internal 

parts. A pressure peak is shown on the pressure gauge during these beats. Avoid to shut down the 
watermaker exactly on the beat, but wait a second after the beat to stop the unit properly. 

 

5.3.2 

Normal operating procedure with final flushing (recommended procedure) 

 
 

1.  Push ON/OFF to start the watermaker.  

 
2.  Push  FLUSHING  to  flush  and  stop  the 
watermaker.  The  watermaker  will  activate  a 
flushing cycle then it will stop after 1 minute. 
 
 
 

 

 

 

Содержание ZEN 30













































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды