manualshive.com logo in svg

Schenker ZEN 30, Инструкция по установке, эксплуатации и обслуживанию

Поделиться
Скачать
Schenker ZEN 30 Скачать руководство пользователя страница 12

 

 

 

3 

– PRESENTATION OF THE PRODUCT                                              COD.

30Z12/24.B.2021

 

EN 

 

THE PRESENT MANUAL BELONGS TO - 

Schenker Italia 

-  ALL RIGHTS RESERVED 

11 

Weight:   

 

 

 

 

 

 

21 Kg 

 
Hydraulic Connection 

Seawater inlet:   

 

 

 

 

hose barb for 16mm internal diameter reinforced hose. 

Brine Discharge:   

 

 

 

hose barb for 16mm internal diameter reinforced hose. 

Fresh water:  

 

 

 

 

 

¼’’ fitting, 6x8mm hose. 

 

PUMP 

Dimensions 

Length:   

 

 

 

 

 

 

23,5 cm 

Width:  

 

 

 

 

 

 

 

22 cm 

Height:   

 

 

 

 

 

 

27 cm 

Weight:   

 

 

 

 

 

 

4,5 Kg 

 

Hydraulic Connection 

Water inlet:   

 

 

 

 

 

 

hose barb for 16mm internal diameter reinforced hose. 

Water outlet:  

 

 

 

 

 

 

hose barb for 16mm internal diameter reinforced hose. 

 
Feed pump type:

   

 

 

 

 

Shurflo diaphragm pump 

 
 

Filters:   

 

 

 

 

 

 

 

n. 1 Cartridge filter 5 microns 2.32" x 5

’’  

n. 1 Active carbon filter 2.32" x 

5”   

 
 

Power supply:

  

 

 

 

 

 

12 VDC +/- 15% (30Z12 version) 

 

 

 

 

 

 

 

 

 

 

 

24 VDC +/- 15% (30Z24 version) 

 
Average electric consumption

:  110 Watt/h average 

 
Nominal fresh water production:

 30 Lit/h +/- 20% @ seawater 25 °C salinity 35.000 ppm 

 

CEE conformity

: 

In  compliance  with  directives  89/392  CEE  sect.1  (general  safety  machines 
requirements),  89/336  CEE  (electromagnetic  compatibility),  73/23  CEE 
(electric safety requirements)   

 

3.6  Features of the product 

The fresh water produced by a Schenker watermaker, obtained by clean seawater, has a high purity. Despite 
this, the potability may not be guaranteed: bacterium caused by non-observance of shutdown and cleaning 
procedures may be present in the watermaker. Therefore, it is essential that the correct shut down and storage 
procedures are followed to ensure continued purity of the  fresh water. UV treatment of the fresh water may 
well be beneficial. 
 

 

Содержание ZEN 30













































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды