IM019
www.scarlett.ru
SC-HC63C14
4
GB
INSTRUCTION MANUAL
IMPORTANT SAFEGUARDS
Please read this instruction manual carefully
before use and keep in a safe place for future
reference.
Before switching on the appliance for the first
time please check if the technical specifications
indicated on the unit correspond to the mains
parameters.
For home use only. Do not use for industrial
purposes. Do not use the appliance for any other
purposes than described in this instruction
manual.
Do not use outdoors.
Always unplug the appliance from the power
supply before cleaning and when not in use.
To prevent risk of electric shock and fire, do not
immerse the appliance in water or any other
liquids. If it has happened DO NOT TOUCH the
appliance, unplug it immediately and check in a
service center.
Do not take this product to a bathroom or use
near water.
The appliance is not intended for use for
physically, sensory or mental disabled person
(including children) or for person with lack of life
experience or knowledge, if only they are under
supervision or have been instructed about the
use of the unit by responsible person.
Children must be under control in order not to be
allowed to play with the appliance.Do not leave
the appliance switched on when not in use.
Do not use other attachments than those
supplied.
Do not operate after malfunction or cord
damage.
In case of power cord is damaged, its
replacement should be done by the manufacture
or service department or the other high-skill
person to avoid any danger.
Do not attempt to repair, adjust or replace parts
in the appliance. Repair the malfunctioning
appliance in the nearest service center.
Keep the cord away from sharp edges and hot
surfaces.
Do not place or store the appliance where it can
fall or be pulled into a tub or sink.
Do not pull, twist, or wrap the power cord around
the appliance.
Never insert any objects into openings in the
appliance housing.
Do not put operating appliance on any surface, it
may cause injury or damage.
Do not use the appliance with damaged comb, or
with teeth missing from the blades as injury may
occur.
If the product has been exposed to temperatures
below 0ºC for some time it should be kept at
room temperature for at least 2 hours before
turning it on.
NOTE: KEEP THE BLADES OILED.
Do not use the hair clipper when the skin is
infected.
Do not use the hair clipper on animals.
The manufacturer reserves the right to introduce
minor changes into the product design without
prior notice, unless such changes influence
significantly the product safety, performance,
and functions.
Production date mentioned on the unit and/or on
the packing materials and documentations.
BLADE ALIGNMENT
Blades must be realigned if they were removed
for cleaning or after replacement.
To realign the blades, simply match the upper
and lower blades teeth up, point for point.
End of top blade teeth should be approximately
1.2 mm back from lower blade. Compare your
clipper blades with the sketch (pic.1).
If blade alignment is incorrect, add a few drops
of oil to the blades, switch on the clipper for a
few moments, switch off and unplug. Loosen
screws slightly and adjust. Tighten screws after
blade is aligned.
OILING
To maintain your clipper in peak condition, the
blades should be oiled after every haircut.
Do not use hair oil, grease, oil mixed with
kerosene or any solvent.
BLADE LEVER
The lever located to the left of the blades, allows
easily adjust cut hair length while clipping.
The lever adds versatility to your clipper by
allowing you gradually change the closeness of
your cut without an attachment comb.
When the lever is in the uppermost position, the
blades will give you the closest cut and leave the
hair very short. Pushing the lever downwards
gradually increases the cutting length.
In its lowest position, the lever will leave the hair
approximately the same length as a №1 (3mm)
comb.
The lever will also extend the use of your blades
since a different cutting edge is used in each
setting.
In addition, if extremely heavy hair cutting has
jammed the blades, it will help you to remove
hair that has become wedged between the two
blades without removing the blades.
While the clipper is running rapidly move the
lever from “close cut” to “longer cut” a couple of
times. Do this each time after you have finished
using your clipper to keep the blades free of cut
hair.
If this does not help and clipper stops cutting,
blades are dulled. Replace them with new
blades.
INSTRUCTIONS FOR HAIR CUTTING
Before first use cutting blades of the machine
should be thoroughly lubricated.
Wipe off any excess oil. This should be done
after each use. While using the unit, untwist the
cord from time to time to avoid tangling.
Before cutting always comb the hair thoroughly
first.
