SBC PCD3 Series Скачать руководство пользователя

Страница: 25 / 133

Saia-Burgess Controls AG

Hardware manual for PCD3 series │ Document 26-789 ENG19│ 2018-06-29

System overview

PCD3.Mxxx0 Classic CPU and expansion enclosure

3-2

3.1

System overview

PCD3.RIO PCD3.LIO

PCD3.LIO

PCD3.CPU

RIO for decentralized tasks

CPU for centralized tasks

-S-

3.1.1

SBC S-Net networking concept

SBC S-Net is the name of the new flexible networking concept for innovative and

economical automation solutions with SaiaPCD.

Based on the open standards Ethernet-TCP/IP (Ether S-net) and Profibus

(Profi S-net): Utilization of existing network infrastructure



no double ca-

bling required

Supports multivendor and multi-protocol operation:

Reduce costs for project planning, programming, commissioning and mainte-

nance thanks to end-to-end use of Ethernet TCP / IP and Profibus with S-Net

for the Private Control Network (PCN) for SaiaPCD

Consistent use of web technologies via Ethernet TCP / IP and Profibus for com

missioning, operation, monitoring and diagnostics

Integrated programming and commissioning via Ethernet TCP / IP and Profibus
Integrated network connections in the base unit Profibus interface integrated in the

operating system of the new PCD3 controllers and PCD3 RIO (included in the

base unit at no extra cost)

Profi-S-Net with optimized protocols and services for the efficient operation of

PCD3 RIO and PCD3 controllers on Profibus

Multi-protocol operation:

The new PCD3 controllers and PCD3 RIOs support Profibus-DP and S-Net on

the same connector

Continuity and investment protection:

Alle Saia PCD systems can be integrated in the concept with the existing Profi

bus and Ethernet TCP / IP connections.

Содержание PCD3 Series






































































































































Результаты поиска

Содержание PCD3 Series

Отзывы:

Похожие инструкции для PCD3 Series

Бренды по названию

Популярные бренды

SBC PCD3 Series, Руководство пользователя

Результаты поиска

Содержание PCD3 Series

Отзывы:

Похожие инструкции для PCD3 Series

Бренды по названию

Популярные бренды