SBC PCD3 Series Скачать руководство пользователя

Страница: 108 / 133

Saia-Burgess Controls AG

Hardware manual for PCD3 series │ Document 26-789 ENG19│ 2018-06-29

Communication interfaces

5-7

Onboard interfaces

Option 1

Configuration with the desired protocol (S-Bus PGU

configuration)

Option 2

Assignment (SASI) in the user program (the port must not be

configured as S-Bus PGU port)

If a programming device is connected again instead of the

peripheral device during operation, the mode is automatically

switched over to PGU (pin 6 logic 1 (DSR), in PGU mode:

DSR PING = 1)

In order to be able to use the interface again for the

connection of a peripheral device, Port 0 must be reconfigured

with the SASI command

GND

SGN

RTS

CTS

RTS

TXD

RXD

PGND

PGU-Plug

D-SUB 9 pol.

(female)

Peripheral

Cable

+5V

(just for PGU)

1) When communicating with terminals, check whether certain connections are to

be bridged or to be set by the command SOCL on 1 or 0. Generally the use of

handshake (RTS / CTS) is recommended (see also manual 26/795, series PCD7.

D23x, graphics terminals).

Option 3

Port 0 can also be used as a modem interface with a 1 to 1 ca-

ble. As described in chapter 7.1.2 Hardware options, the check

box Full RS-232 handshaking on port 0 must be selected.

Option 4

With connection cable PCD8.K111, this interface can be used as

a programming device connection.

SGN

DSR

SGN

RTS
CTS

CTS

RTS

DTR

PCD

D-SUB 9 pol.

(female)

D-SUB 9 pol.

(male)

Connection cable PCD8.K111

Содержание PCD3 Series






































































































































Результаты поиска

Содержание PCD3 Series

Отзывы:

Похожие инструкции для PCD3 Series

Бренды по названию

Популярные бренды

SBC PCD3 Series, Руководство пользователя

Результаты поиска

Содержание PCD3 Series

Отзывы:

Похожие инструкции для PCD3 Series

Бренды по названию

Популярные бренды