SBC PCD3 Series Скачать руководство пользователя

Страница: 105 / 133

Saia-Burgess Controls AG

Hardware manual for PCD3 series │ Document 26-789 ENG19│ 2018-06-29

Communication interfaces

5-4

Serial interfaces log

5.2.1

Serial S-Net

Supports the S-Bus protocol on serial interfaces (RS-232, RS-485/422, modem) in

master/slave operation. The SBC S-Bus S-Bus with its simple and secure protocol

is already available as standard on all Saia PCD

Technical data

Transmission rates:

up to 115 kbps protocol S-Bus, high net data rates thanks

to low protocol overhead

Number of stations:

up to 254 stations in segments of 32 stations each

Port in the PG5:

0, 1, 2, 3,100, 101, 110, 111, 120, 121, 130, 131

5.2.2

Profi S-Net

Private Control Network (PCN) includes all protocols and services for the operation

of SBC devices (PLC, RIO, HMI, PG) on Profibus. Multi-protocol operation is

supported on the same connector and cable.

Technical data

Transmission rates:

up to 1.5 Mbit/s

Number of stations:

up to 124 stations in segments of 32 stations each

Logs:

Profi S-Bus, Profi S-I/O, DP slave, HTTP

Port in the PG5:

2 and 10

5.2.3

Ether S-Net

Private Control Network (PCN) includes all protocols and services for the operation

of SBC devices (PLC, RIO, HMI, PG) on Ethernet supports multi-protocol

operation (S-Bus, S-IO, HTTP, SMTP) on the same connector and cable.

Technical data

Connection:

10 Base-T/100 Base TX (RJ-45)

Speed:

10/100 MBit/s (autosensing)

Logs:

TCP/IP or UDP/IP, Ether S-Bus, Ether-S-I/O, HTTP,

SMTP

Port in the PG5:

5.2.4

Logs implemented in the user program

Based on the character mode, various protocols can be implemented (with very

good knowledge of STL programming).

Our system partners have already done this for a large number of protocols,

allowing our controllers to communicate with components from a wide range of

manufacturers, e.g. via Modbus, M-Bus etc.

Please refer to the link page

www.sbc-support.com

for links to the system

partners.

Содержание PCD3 Series






































































































































Результаты поиска

Содержание PCD3 Series

Отзывы:

Похожие инструкции для PCD3 Series

Бренды по названию

Популярные бренды

SBC PCD3 Series, Руководство пользователя

Результаты поиска

Содержание PCD3 Series

Отзывы:

Похожие инструкции для PCD3 Series

Бренды по названию

Популярные бренды