manualshive.com logo in svg

SawStop CTS-120A60, Руководство пользователя

Поделиться
Скачать
SawStop CTS-120A60 Скачать руководство пользователя страница 35

11. Plug the cord into a wall outlet, and then turn the 

saw on to confirm the system initializes as normal, 

as indicated by a solid green status light.

If the system does not initialize properly, contact the 

SawStop Service department (

see page 56

).

Inspect the Blade Guard

Check the blade guard before each use. Keep the 

blade guard free of accumulated saw dust, wood 

chips, and other debris. Check that you have a clear 

view of the saw blade from all angles; make sure no 

abrasions or materials on the blade guard obscure 

your view. Check that the blade guard pivots up and 

down freely. The blade guard should rest completely 

on the table when not in use.

How to Inspect the Side Guards

Confirm the side guards (A) (both sides) swing freely.

The front side guard should contact (A) the table when 

you set the bevel of the blade to 45 degrees.

How to Inspect the Anti-Kickback 

Pawls

Confirm the anti-kickback pawls engage a workpiece. 

To test, with the power off and the blade lowered, 

push a workpiece under a pawl, and then try to pull 

the workpiece back towards the front of the saw. The 

pawl should prevent you from pulling the workpiece. If 

not, make sure the pawls are correctly installed 

(

see page 18

). If installed correctly and the pawls 

still don’t engage the workpiece, replace the pawls 

(

see page 33

).

How to Cut a Slot in a 

Replacement Insert

The blade slot in the insert that came with your saw 

was pre-cut at the factory. For replacement inserts, 

you must cut the slot. Create the slot using two cuts: 

one at 90 degrees and one at 45 degrees.

 

Do not use a replacement insert without first 

cutting the slot.

 

Always turn off and unplug the saw when 

working on or maintaining the saw.

1.  With the blade lowered, remove the old insert and 

install the new insert (A).

 

Make sure the riving knife is not installed when 

creating the slot.

2.  Clamp a board (B) over the insert to make sure the 

insert remains solidly locked in place while cutting 

the slot.

A

A

A

!

!

A

!

B

SawStop

®

 Compact Table Saw 

|

 35

Содержание CTS-120A60

























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды