Savaria omega страница 29 Скачать руководство пользователя | Manualshive

Страница: 29 / 34

background image

Page 29

Part No. 000823, 06-m02-2012

OMEGA IPL Installation Guide

Before leaving job site

Before leaving the job site, make sure the work area is

clean and the lift is safe and operational.

Procedure

1

Clean up the work area.

2

Make sure all hardware has been tightened.

3

Make sure that all data plates, tags and instruction
labels are present.

4

Explain the operation of the lift to the customer.

5

Assist the customer on an orientation ride.

6

Provide a copy of the Owner’s Manual and Warranty to
the customer. Record all required details per the
Owner’s Manual.

Installation notes

Use this section to record any site-specific notes.

_______________________________________________

_______________________________________________

_______________________________________________

_______________________________________________

_______________________________________________

_______________________________________________

_______________________________________________

_______________________________________________

_______________________________________________

_______________________________________________

_______________________________________________

_______________________________________________

_______________________________________________

_______________________________________________

_______________________________________________

_______________________________________________

_______________________________________________

_______________________________________________

_______________________________________________

_______________________________________________

_______________________________________________

_______________________________________________

_______________________________________________

_______________________________________________

_______________________________________________

_______________________________________________

_______________________________________________

_______________________________________________

_______________________________________________

_______________________________________________

_______________________________________________

_______________________________________________

«
...
27
28
29
30
31
...
»

Содержание omega



































Отзывы:

Нет отзывов

Похожие инструкции для omega

Бренд: Accu-Sort Страницы: 22

Бренд: HALDER Страницы: 2

Бренд: The Handy Страницы: 4

Бренд: CEA Страницы: 92

Бренд: Dhollandia Страницы: 82

Бренд: LSP inc. Страницы: 6

HRU-WALL Series

Бренд: Nalnor Страницы: 28

Бренд: OMCN Страницы: 40

Бренд: 4CR Страницы: 7

Rotational R-450A

Бренд: Global Lift Страницы: 49

Бренд: ROTOTILT Страницы: 17

Бренд: Miller Страницы: 136

Бренд: ITR Страницы: 15

RaptorX-SL1200-S15

Бренд: CNC-Step Страницы: 102

TRAILBLAZER 302 AIR PAK

Бренд: Miller Страницы: 72

VRV 5 BS4A14AJV1B

Бренд: Daikin Страницы: 44

ePowerSwitch 8 Master

Бренд: Neol Страницы: 2

JACKSHAFT MOTOR-CONTROL SYSTEM 815-RL

Бренд: Zap Страницы: 28

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды