This Quick Reference Guide provides all the steps necessary to
install the 16-channel AMP-2000 amplifier.
The following units are supported in this document:
•
AMP-2000-00 (North America)
•
AMP-2000I-00 (International)
Box Contents
(1) Savant 16 Channel Amplifier (AMP-2000-xx or AMP-2000I-xx)
(2) Rack Mounting Brackets
(8) Pan Head Phillips Screws for Brackets (M3 x 8 mm)
(1) AC Power cord - 6 ft
(4) 4-pin Screw Down Plug-in Connectors
(4) Rubber Chassis Feet
(1) Trigger Cable - 2.5 mm (3/32”) Mono to 3.5 mm (1/8”) Mono
(1) Quick Reference Guide (this document)
Note:
The AMP-2000/2000I will be referred to as the AMP-2000 unless
otherwise specified.
Specifications
Environmental
Environmental
Temperature
32° to 104° F (0° to 40° C)
Humidity
10% to 80% Relative Humidity (non-condensing)
Cooling
202 cubic feet per minute (CFM) recommended
BTU
3925 BTU/hr
Dimensions and Weight
Dimensions and Weight
Height
5.21 in (13.23 cm)
Width
17.30 in (43.94 cm)
Depth
15.00 in (38.20 cm)
Weight
Shipping: 44 lb (19.5 kg)
Power
Power
Input Power
120V AC 10A 60 Hz - AMP-2000-00
(N. America)
230V AC 5A 50 Hz - AMP-2000I-00
(International)
Fuse Rating
T15AH/250V (120V) (N. America)
Fuse Rating
T8AL/250V (230V) (International)
Maximum Power
1150 watts
Operating Parameters
Operating Parameters
Rated Power
40 WPC at 8 ohms, 50 WPC at 4 ohms; (0.1%
THD+N, 1kHz)
Input Impedance
33k ohms
Input Sensitivity
750mV for 40W at 8 ohms
Overall Voltage
Gain
27.5dB
Frequency
Response
Bandwidth limited from 20Hz to 20kHz
+0.8dB
Distortion, THD+N
< 0.07% THD+N from 20Hz to 20kHz, All
channels driven at 8 ohms (1 Watt)
Signal-to-Noise
Ratio
>90dB
Input Triggers
3 – 24V AC/DC 5mA
Output Triggers
12V DC 100mA
Regulatory
Regulatory
Safety and
Emissions
FCC Part 15 | UL-60065
RoHS
Compliant
Minimum Supported Release
Minimum Supported Release
Savant OS
da Vinci 5.1.1
Front Panel
Power Button
(Master)
Turns the amplifier On or O
ff
based on the Turn
On Mode settings.
See
Setting the Amplifiers Turn On Mode
for
details.
Power LED
Indicates the power state of the amplifier:
Red:
Amplifier is in Standby Mode.
Green
: Amplifier is On.
O
ff
:
No power is supplied to the amplifier.
Protection
Status
Indicators
(LED)
Indicate the status of each zone or pair of
channels when in the central potential
protection mode.
Red:
The central potential protection mode has
been enabled to protect a zone/channel.
See
for details.
O
ff
:
The central potential protection mode has
not been enabled.
Rear Panel
Turn-on Mode
Switch
Provides three options for turning the
AMP-2000 On and O
ff
.
• Constant (manual turn-on via the front panel
master Power button)
• Audio Sense
• 3-24 AC/DC Voltage Trigger (External)
See
Setting the Amplifiers Turn On Mode
for
details.
3-24V AC/DC
Voltage
Trigger
3-24V AC/DC - 3.5 mm (1/8”) Mono jack
Used to control the power state of the amplifier
when Turn-on Mode switch is set to 3-24 AC/
DC Voltage Trigger mode.
12V Trigger
Control
Output
12V DC 100mA - 2.5 mm (3/32”) Mono jack
Used to trigger an additional AMP-2000 or
other device that is activated by receiving a 12V
DC 100mA signal. This voltage is present only
when the amplifier is active or on.
See
for details
Gain
Independent gain controls allowing for fine-
tuning the output level of each channel.
Audio Source
Inputs
RCA Stereo (L&R) line-level analog audio
inputs.
Speaker
Connections
4-pin Screw Down Plug-in Connectors
Note:
Specify 4 or 8 ohm speakers when
designing the system.
Power Input
IEC 320 power connector with 3-pole
detachable power cord.
Fuse
T15AH/250V (120V) (N. America)
T8AL/250V (230V) (International)
AMP-2000-00/AMP-2000I-00 | 009-0421-04 | 150407
AMP-2000-00/AMP-2000I-00 | 009-0421-04 | 150407
45 Perseverance Way, Hyannis, MA 02601
Copyright © 2015 Savant Systems, LLC
1 of 2
Savant® 16 Channel Amplifier
Quick Reference Guide
For Product Info
