sauter Equitherm EQJW 125 Скачать руководство пользователя страница 37

Страница: 37 / 74

EQJW 125: Heating controller

Operation

7001029003 A

4.4.1

Calling up the weekly switching programme

Set the rotary switch to PROG.

Push the input knob.

•

The weekly programme is selected.

Turn the input knob.

Select the day of the week.

(1 = Monday, 2 = Tuesday, ..., 1 - 7 = daily).
5 = Friday has been selected here.

Push the input knob.

•

The first switching command for this day
(or for the whole week) is shown.

4.4.2

Viewing switching commands

Turn the input knob; the individual switching
commands are shown.

•

An empty switching command is shown as
'_ _ _ _'.

4.4.3

Entering a switching command

Turn the input knob until you reach the next

empty switching command.

Push the input knob.

•

The new switching command is shown.

Turn the input knob.

•

The time for the switching command is
changed.

Push the input knob.

•

The time for the switching command is
confirmed.

Turn the input knob.

Select the mode for the switching command.

Push the input knob.

•

The mode is confirmed.

Содержание Equitherm EQJW 125











































































Результаты поиска

Содержание Equitherm EQJW 125

Отзывы:

Похожие инструкции для Equitherm EQJW 125

Бренды по названию

Популярные бренды

sauter Equitherm EQJW 125, Руководство пользователя

Результаты поиска

Содержание Equitherm EQJW 125

Отзывы:

Похожие инструкции для Equitherm EQJW 125

Бренды по названию

Популярные бренды